DYNAMIC RADAR CRUISE CONTROL SYSTEM


  1. FUNCTION OF MAIN COMPONENTS


    1. The main components in the dynamic radar cruise control system have the following functions:

      Component Function
      Cruise Control Main Switch Main Switch Turns on/off the power to the dynamic radar cruise control system.
      MODE Switch Switches the control mode between the constant speed control mode and vehicle-to-vehicledistance control mode.
      CANCEL Switch A cancel signal can be output to the ECM through the operation of this switch.
      RES/+ Switch The acceleration function and resume control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated.
      SET/- Switch The deceleration function and set control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated.
      Distance Control Switch While the system is in the vehicle-to-vehicle distance control mode, the driver can operate the distance control switch to select the vehicle-to-vehicle distance in 3 stages: long, middle, and short.
      Windshield Wiper Switch Assembly Transmits a windshield wiper switch signal to the driving support ECU.
      Stop Light Switch Assembly Detects the depressing of the brake pedal and transmits a signal to the ECM.
      Millimeter Wave Radar Sensor Assembly Radiates millimeter waves forward, uses the reflected millimeter waves for detecting the presence of a vehicle being driven ahead, the vehicle-to-vehicle distance, and the relative speed, and transmits these pieces of information to the driving support ECU.
      Steering Angle Sensor Detects the angle and direction of steering and transmits signals to the skid control ECU and driving support ECU.
      Yaw Rate Sensor Detects the yaw rate of the vehicle and transmits signals to the skid control ECU and driving support ECU.
      Speed Sensor Detects the vehicle speed and transmits a signal via the skid control ECU to the combination meter assembly.
      Throttle Body Throttle Control Motor Adjusts the throttle valve to the limiter position in accordance with signals from the ECM.
      Throttle Position Sensor Transmits the throttle valve position information to the ECM.
      Combination Meter Assembly Cruise Main Indicator Light

      • Illuminates when the constant speed control mode is on.

      • If the ECM detects a malfunction, this light blinks to warn the driver.
      Radar Cruise Indicator Light

      • Illuminates when the vehicle-to-vehicle distance control mode is on.

      • If the ECM detects a malfunction, this light blinks to warn the driver.
      Cruise SET Indicator Light Illuminates when the constant speed control mode or the vehicle-to-vehicle distance control mode is set.
      Multi-information Display During the vehicle-to-vehicle distance control, the multi-information display receives signals from the driving support ECU, in order to display the system conditions.
      Master Warning Light Illuminates when there is a malfunction in the system.
      Multi Buzzer If the ECM and driving support ECU detect automatic cancel or warning signals while the vehicle is operating under cruise control, the multi buzzer sounds to inform the driver.
      Driving Support ECU While the system is in the vehicle-to-vehicle distance control mode, the driving support ECU detects the vehicle being followed based on signals from the millimeter wave radar sensor assembly. Then, the driving support ECU calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicledistance, and outputs a request signal to the ECM and/or skid control ECU.
      ECM

      • Controls the constant speed control mode in accordance with signals from the switches and sensors.

      • If the ECM detects a malfunction in the dynamic radar cruise control system, it will store a Diagnostic Trouble Code (DTC).
      4WD Control ECU Sends a dynamic radar cruise control system cancel signal to the driving support ECU if an abnormality occurs when the drive mode is switched between low and high, when the center differential lock is switched, etc.
      Park/Neutral Position Switch Assembly Detects the shift position and transmits a signal to the ECM.
      Skid Control ECU While the system is operating in vehicle-to-vehicle distance control mode, the skid control ECU actuates the brake actuator in accordance with the brake request signal received from the driving support ECU. In addition, the ECU transmits signals such as wheel speed and estimated vehicle acceleration speed to the driving support ECU.
      Brake Actuator Assembly Actuates the brakes in accordance with the signals from the skid control ECU.
      Driving Support Switch Control ECU Sends a dynamic radar cruise control system cancel signal to the driving support ECU in accordance with the mode status of the multi-terrain select.

  2. FUNCTION


    1. Control of Dynamic Radar Cruise Control System Varies Depending on Mode


      1. A: Constant speed control mode

      2. B: Vehicle-to-vehicle distance control mode

        Function Outline Mode A Mode B
        Constant Speed Control The ECM compares the actual vehicle speed and the set speed. If the vehicle speed is higher than the set speed, it uses the throttle control motor to decrease the throttle opening. If the actual vehicle speed is lower than the set speed, it uses the throttle control motor to increase the throttle opening. ○ ○
        Deceleration Control Effects throttle control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicledistance between the driver's own vehicle and the vehicle ahead equals the set distance. - ○
        Follow-up Control After effecting deceleration control, the vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance in accordance with the vehicle speed. - ○
        Acceleration Control Accelerates the vehicle in order to attain the set vehicle speed if the vehicle or the vehicle ahead has changed lanes. - ○
        Set Control When the shift lever is in D and the cruise control main switch is pressed to the SET/- direction and released when the main switch on the cruise control main switch has been pressed to turn the system on, the ECM stores the vehicle speed and maintains the vehicle constantly at that speed. ○ ○

        The vehicle is running within the following speed range:


        • Approx. 50 km/h to 200 km/h (30 mph to 125 mph)

        		 ○ -

        The vehicle is running within the following speed range:


        • Approx. 50 km/h to 170 km/h (30 mph to 105 mph)

        		 - ○
        Low Speed Limit Control The low speed limit is the lowest speed that the dynamic radar cruise control system can be set at and it is designed to be approx. 40 km/h (25 mph). The dynamic radar cruise control system cannot be set below this speed. If the vehicle speed drops below this speed while the dynamic radar cruise control system is running, the dynamic radar cruise control system will be canceled automatically. However, the set speed is kept in the memory. ○ ○
        Coast Control While the cruise control main switch is held to the SET/- direction, the vehicle speed and the set speed change as follows, in accordance with the mode: ○ ○

        • The vehicle decelerates constantly.

        • The set speed changes to the speed at which the switch was turned off.

        		 ○ -

        • The set speed decreases in increments of 5 km/h or 5 mph.

        • The vehicle decelerates rapidly due to ETCS-i.

        		 - ○
        Tap-down Control

        When the cruise control main switch is pushed momentarily (approx. 0.6 seconds) to the SET/- direction, the vehicle speed and the set speed change as follows, in accordance with the mode:


        • The set speed will decelerate in increments of approx. 1.6 km/h (1 mph) each time the switch is pressed.

        • However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed will change to the speed at which the vehicle was being driven at the time the switch was operated.

        		 ○ -
        When the cruise control main switch is pushed momentarily (approx. 0.6 seconds) to the SET/- direction, the vehicle will decelerate in increments of approx. 5 km/h (5 mph)*1 or 1 km/h (1 mph)*2 each time the switch is pressed. - ○
        Accelerator Control When the cruise control main switch is pushed to the RES/+ direction and held, the vehicle speed and the set speed change as follows, in accordance with the mode: ○ ○

        • The vehicle will accelerate constantly.

        • The set speed changes to the speed at which the switch was turned off.

        		 ○ -

        • The set speed increases in increments of 1 km/h or 1 mph.

        • The vehicle will accelerate to the speed that is set at the time the switch is released.

        • However, only the set speed will change during follow-up control.

        		 - ○
        Tap-up Control

        When the cruise control main switch is pushed momentarily (approx. 0.6 seconds) to the RES/+ direction, the vehicle speed and the set speed change as follows:


        • The vehicle will accelerate in increments of approx. 1.6 km/h (1 mph) each time the switch is pressed.

        • However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed does not change.

        		 ○ -
        When the cruise control switch is pushed momentarily (approx. 0.6 seconds) to the RES/+ direction, the vehicle will accelerate in increments of approx. 5 km/h (5 mph)*1 or 1 km/h (1 mph)*2 each time the switch is pressed. - ○
        Resume Control

        • When the driver pushes the cruise control main switch to the RES/+ direction after the vehicle speed has exceeded the low speed limit, the dynamic radar cruise control system resumes operation to reach the vehicle speed that was set at the time the driver canceled the dynamic radar cruise control system.

        • Even if the vehicle speed drops below the low speed limit, resume can be performed when the vehicle speed exceeds the low speed limit.

        		 ○ ○
        If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set speed. At this time, the vehicle speed can be increased promptly by pushing the cruise control main switch to the RES/+ direction. - ○
        Shift Down Control When the vehicle is traveling uphill using cruise control, automatic transmission control may cause the transmission to shift down. During shift down control, when the end of uphill travel is determined, the transmission will shift up after a certain period of time. When the transmission shifts down during the accelerator control or the resume control, the transmission will shift up after the accelerator control or the resume control ends. ○ ○
        Manual Cancel Control

        If any of the following conditions is met, the dynamic radar cruise control system will be canceled:


        • A stop light switch on signal is sent to the ECM (the brake pedal is depressed).

        • The shift lever is moved from D to N.

        • The 1st, 2nd or 3rd range is selected in the S mode position.

        • A CANCEL switch on signal is sent to the ECM (the cruise control main switch is moved to the CANCEL direction).

        • A main switch off signal is sent to the ECM.

        • A VSC operation signal is sent to the ECM.

        • A cancel request is received from the 4WD control ECU.

        		 ○ ○
        Automatic Cancel Control When an automatic cancel signal is sent to the ECM, the dynamic radar cruise control system operation is canceled. At this time, the warning method and the control resumption condition vary in accordance with the cancel signal. ○ ○
        Mode Switching Control

        The following operations switch the modes:

        1) Main switch on the cruise control main switch is on (starts in the vehicle-to-vehicle distance control mode).

        2) Cruise control main switch is held to the MODE direction (approx. 1 second or more). If the switch is pushed in any other direction before switching modes, switch the dynamic radar cruise control system off, then perform steps 1) and 2) again.

        		 ○ ○
        Diagnosis If a malfunction occurs in the dynamic radar cruise control system during the system operation, the ECM cancels dynamic radar cruise control system and diagnoses and memorizes the faults related to the malfunction. ○ ○

        • *1: Models for Europe

        • *2: Except models for Europe

    2. Constant Speed Control Function in Vehicle-to-vehicle Distance Control Mode


      1. The millimeter wave radar sensor assembly transmits the information about the vehicle ahead to the driving support ECU and also transmits a millimeter wave radar sensor assembly operation signal to the ECM. The driving support ECU transmits this signal to the ECM.

      2. The ECM compares the set speed and the actual vehicle speed, and effects constant speed control by regulating the throttle control in order to attain the set speed.

        A019QXLE02

    3. Deceleration Control Function


      1. The driving support ECU calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor assembly, and transmits a deceleration request signal to the ECM.

      2. The ECM closes the throttle valve upon receiving this signal in order to cause the vehicle to decelerate.

      3. This control is not effected in the presence of a parked vehicle or object, or below the settable vehicle speed range.

        A019R18E02

      4. If the driving support ECU determines that further deceleration is necessary, it transmits a brake request signal to the ECM. Upon receiving this signal, the ECM transmits a brake request signal to the skid control ECU. The skid control ECU then controls the brake actuator assembly to apply the brakes.

      5. At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop light control ECU assembly, in order to inform anyone who might be following the vehicle.

        A019QO2E02

      6. If further deceleration is necessary after the stop light is illuminated, the skid control ECU sounds the skid control buzzer assembly based on the request signal from the driving support ECU to urge the driver to depress the brake pedal.

        A019QI8E02

    4. Follow-up Control Function


      1. After effecting deceleration control, the driving support ECU transmits a request signal to the ECM so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicledistance in accordance with the vehicle speed.

      2. The ECM regulates the throttle upon receiving this signal in order to effect follow-up control.

      3. 3 stages (long, middle, and short) of vehicle-to-vehicle distance can be selected by operating the distance control switch.

        A019R45E02

    5. Acceleration Control Function


      1. If the driving support ECU detects (based on the millimeter wave radar sensor assembly) that either the vehicle or the vehicle ahead has changed lanes, an acceleration request signal is transmitted to the ECM in order to attain the set vehicle speed.

      2. The ECM regulates the throttle upon receiving this signal in order to effect acceleration control.

        A019QV4E02

    6. Automatic Cancel Control Function


      1. If any of the conditions listed below occurs while the vehicle is in cruise control (A: constant speed control mode, B: vehicle-to-vehicle distance control mode), the cruise control will be canceled.

      2. The following items are used as a warning on the automatic cancel control function:


        • a: Multi-information display (shows warning message)

        • b: Master warning light

        • c: Multi buzzer

        • d: Cruise main indicator light

        • e: Radar cruise indicator light

        Mode Description of Malfunction Warning
        A and B

        If any of the conditions listed below occurs, the ECM clears the set speed and cancels the cruise control:


        • Malfunction of the vehicle speed signal

        • An open or short circuit in the stop light switch

        The cruise control is prohibited until the conditions are restored or the dynamic radar cruise control system is turned off and back on again using the main switch on the cruise control main switch.

        a: "CHECK CRUISE CONTROL SYSTEM"

        b: Illuminates

        c: Sounds once

        d: Blinks (in the case of A)

        e: Blinks (in the case of B)

        If the condition below occurs, the ECM clears the set speed and cancels the cruise control:


        • The ETCS-i has a malfunction.

        The cruise control is prohibited until the conditions are restored or the dynamic radar cruise control system is turned off and back on again using the main switch on the cruise control main switch.

        a: -

        b: -

        c: -

        d: -

        e: -

        If the condition below occurs, the ECM cancels the cruise control while retaining the set speed in its memory:


        • The vehicle speed drops below the low speed limit (approx. 40 km/h [25 mph]).

        a: -

        b: -

        c: Sounds once

        d: -

        e: -
        A

        If the condition below occurs, the ECM cancels the cruise control:


        • The vehicle speed drops more than 16 km/h (10 mph) below the set speed.

        a: -

        b: -

        c: -

        d: -

        e: -
        B

        If any of the conditions listed below occurs, the ECM clears the set speed and cancels the cruise control:


        • Malfunction of the millimeter wave radar sensor assembly

        • Displacement of the axis of the millimeter wave radar sensor assembly

        • Malfunction in the dynamic radar cruise control system other than those given above

        The cruise control is prohibited until the engine switch is turned on (IG) again.

        a: "CHECK CRUISE CONTROLSYSTEM"

        b: Illuminates

        c: Sounds once

        d: -

        e: Blinks

        If the condition below occurs, the ECM cancels the cruise control while retaining the set speed in its memory:


        • The millimeter wave radar sensor assembly is dirty.

        The cruise control is prohibited until the conditions are restored or the main switch on the cruise control main switch is turned on again.

        a: "CLEAN RADAR SENSOR"

        b: Illuminates

        c: Sounds once

        d: -

        e: Blinks

        If any of the conditions listed below occurs, the ECM cancels the cruise control while retaining the set vehicle speed in its memory:


        • The wipers operate at high speed (including AUTO mode).

        • The measurement becomes extremely unstable due to poor weather conditions.

        • In the 2nd start mode.

        • Multi-terrain select is on.

        The cruise control is prohibited until the conditions are remedied or the dynamic radar cruise control system is turned off and back on again using the main switch on the cruise control main switch.

        a: "CRUISE CONTROL NOTAVAILABLE"

        b: Illuminates

        c: Sounds once

        d: -

        e: Blinks

  3. DIAGNOSIS


    1. If a malfunction occurs in the dynamic radar cruise control system, the ECM cancels the dynamic radar cruise control system. The ECM blinks the cruise main indicator light or the radar cruise indicator light and displays a warning message on the multi-information display to inform the driver of the malfunction. At this time, the ECM memorizes the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC). For details of the DTC, refer to the Repair Manual.