QUARTER PANEL ASSEMBLY REPLACEMENT

A00255Q

    Quarter Panel Replacement Using Adhesive

  1. Cut the wheel arch portion.

  2. Heat the quarter panel adhesive area and remove the quarter panel.

    Tech Tips

    Using an industrial heater gun or gas burner, heat the quarter panel to 110 to 140°C. Make sure the quarter panel does not warp.

  3. Clean off any adhesive that remains on the vehicle.

    Tech Tips


    • Using an industrial heater gun or gas burner, heat the adhesive to 110 to 140°C.

    • Using a scraper, scrape away the adhesive.

    • If adhesive remains, the strength of any subsequently applied adhesive will be weak.

  4. Using a disc sander or belt sander, scuff and sand any adhesive that remains on the vehicle.

    Tech Tips

    Scuff at a width of approximately 10 mm (0.39 in.) over the previous adhesive coating.

  5. Apply adhesive to the exposed metal areas on the vehicle. Using a spatula, spread the adhesive evenly.

  6. Apply adhesive to the vehicle again.

  7. Using #60-120 grit sandpaper, scuff the adhesive application area on the new quarter panel.

  8. Apply adhesive to the new quarter panel. Using a spatula, spread the adhesive evenly.

  9. Using a vise grip or the palms of your hands, press the quarter panel so that the thickness of the adhesive is even.

  10. Complete installation the new quarter panel.

  11. Dry the adhesive areas of the new quarter panel.

    Tech Tips


    • With dryer or equivalent (60°C): 60 minutes (complete hardening: 90 minutes)

    • Ambient temperature (25°C): 12 hours (complete hardening: 24 hours)


  1. REMOVAL

    Symbol Meaning
    A002563 Remove Weld Points
    A00257N Remove Weld Points
    A0025AX Remove Weld Points
    A0025C9 Cut with Disc Sander etc.
    A0025I7 Cut and Join Location
    A002561 Cut Location for Supply Parts

      REMOVAL POINT

    1. *a in the illustration indicates the laser screw welding location.

    2. After grinding off the hemming location, remove the quarter panel.

    3. Bend in the same way as *b.

    4. *c in illustration above indicates where the adhesive is located.

    5. Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

      Tech Tips

      In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.

    A00256UC01
    *d Hemming Location *e Disc Sander
    A0025GD Laser Screw Welding - -
    A0025IPC02
    *A RH - -

  2. INSTALLATION

    Symbol Meaning
    A00258K Spot Weld
    A0025D7 Plug Weld
    A0025AO Plug Weld
    A0025EP Plug Weld
    A0025BS Butt Weld
    A002556 Body Sealer

      INSTALLATION POINT

    1. Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

    2. Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

    3. *a in the illustration indicates the laser screw welding location.

    4. When welding *b, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

    5. Before installing a new part, apply body sealer.

      Tech Tips


      • Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

      • Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.

    6. Apply adhesive (3MTMAutomixTMPanel Bonding Adhesive #8115) to the area indicated by *c in the illustration.

      Tech Tips

      Apply enough adhesive to the panels.

    7. Apply adhesive (3MTMAutomixTMPanel Bonding Adhesive #8115) to the area indicated by *d in the illustration.

      Tech Tips


      • Apply a light coat of adhesive around the plug welding points.

      • Apply enough adhesive to the panels.

    8. Bend the flange hem with a wooden hammer and dolly.

      Tech Tips


      • Bend the panel gradually so as not to distort it.

    9. After welding, apply body sealer to the corresponding parts. (See the painting / coating)

    10. After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

    11. After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.

    A0025CZC01
    *A w/ Blind Spot Monitor System: - -
    *1 QUARTER PANEL *2 SIDE PANEL REAR END PATCH
    *e 5 mm (0.20 in.) *f Cloth Tape
    *g Dolly *h Wooden Hammer
    A0025GD Laser Screw Welding - -
    A00257OC01
    *A RH - -