FIT STANDARD / ADJUSTMENT METHOD ADJUSTMENT


  1. INSPECT HOOD SUB-ASSEMBLY


    1. Check that the clearance measurements of areas "a" through "e" are within each standard range.

      A002L92E01
      Standard Clearance
      Area Measurement Area Measurement
      a 2.35 to 5.35 mm (0.0925 to 0.211 in.) b -1.4 to 1.6 mm (-0.0551 to 0.063 in.)
      c 8.70 mm (0.343 in.) d 2.0 to 5.0 mm (0.0787 to 0.197 in.)
      e -1.4 to 1.6 mm (-0.0551 to 0.063 in.) - -

  2. ADJUST HOOD SUB-ASSEMBLY

    A002LBC

    1. Horizontally and vertically adjust the hood.


      1. Loosen the 4 hinge bolts of the hood.

      2. Adjust the clearance between the hood and front fender by moving the hood.

      3. Tighten the 4 hinge bolts after the adjustment.

        Torque:
        13 N*m  { 133 kgf*cm, 10 ft.*lbf }
    2. A002LFU

      Adjust the height of the front end of the hood using the hood bumper cushions.


      1. Adjust the 2 hood bumper cushions so that the heights of the hood and fender are aligned.

        Tech Tips

        Raise or lower the front end of the hood by turning the 2 cushion rubbers.

    3. Remove the cool air intake duct seal.

    4. w/ Dynamic Radar Cruise Control System:


      1. Remove the millimeter wave radar sensor assembly.

    5. A002L9C

      Adjust the hood lock.


      1. Loosen the 3 bolts.

      2. Tighten the bolts after adjustment.

        Torque:
        8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      3. Check that the striker can engage with the hood lock smoothly.

    6. Install the cool air intake duct seal.

    7. w/ Dynamic Radar Cruise Control System:


      1. Install the millimeter wave radar sensor assembly.

  3. INSPECT FRONT DOOR


    1. Check that the clearance measurements of areas "a" through "t" are within each standard range.

      A002LG3E03
      Standard Clearance
      Area Measurement Area Measurement
      a 3.35 to 6.35 mm (0.132 to 0.250 in.) b 1.35 to 4.35 mm (0.0531 to 0.171 in.)
      c 3.35 to 6.35 mm (0.132 to 0.250 in.) d 1.05 to 4.05 mm (0.0413 to 0.159 in.)
      e 3.35 to 6.35 mm (0.132 to 0.250 in.) f 0.85 to 3.85 mm (0.0335 to 0.152 in.)
      g 3.35 to 6.35 mm (0.132 to 0.250 in.) h 2.05 to 5.05 mm (0.0807 to 0.199 in.)
      i 2.8 to 5.8 mm (0.110 to 0.228 in.) j -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      k 2.3 to 5.3 mm (0.0906 to 0.209 in.) l -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      m 2.3 to 5.3 mm (0.0906 to 0.209 in.) n -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      o 3.65 to 6.65 mm (0.144 to 0.262 in.) p 3.65 to 6.65 mm (0.144 to 0.262 in.)
      q 2.0 to 5.0 mm (0.0787 to 0.197 in.) r -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      s 2.0 to 5.0 mm (0.0787 to 0.197 in.) t -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

  4. ADJUST FRONT DOOR

    A002L9R

    Note

    Make sure to turn the engine switch off when adjusting door lock strikers.


    1. Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

      SST
      09812-00010

    2. Tighten the 4 hinge bolts on the vehicle body after adjustment.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

    3. Loosen the 4 hinge bolts on the door and adjust the door position.

    4. Tighten the 4 hinge bolts on the door after adjustment.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }
    5. A002LD5

      Disengage the 4 claws and front door lock striker cover.

    6. A002L99

      Using a T40 "TORX" socket wrench, slightly loosen 2 the striker mounting screws.

    7. Using a brass bar and a hammer, hit the striker to adjust its position.

    8. Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

    9. Engage the 4 claws to front door lock striker cover.

  5. INSPECT REAR DOOR


    1. Check that the clearance measurements of areas "a" through "q" are within each standard range.

      A002LEJE03
      Standard Clearance
      Area Measurement Area Measurement
      a 3.35 to 6.35 mm (0.132 to 0.250 in.) b 1.3 to 4.3 mm (0.0512 to 0.169 in.)
      c 3.35 to 6.35 mm (0.132 to 0.250 in.) d 1.7 to 4.7 mm (0.0669 to 0.185 in.)
      e 3.35 to 6.35 mm (0.132 to 0.250 in.) f 1.6 to 4.6 mm (0.0630 to 0.181 in.)
      g 2.0 to 3.5 mm (0.0787 to 0.138 in.) h -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
      i 3.65 to 6.65 mm (0.144 to 0.262 in.) j 3.65 to 6.65 mm (0.144 to 0.262 in.)
      k 3.65 to 6.65 mm (0.144 to 0.262 in.) l 2.3 to 5.3 mm (0.0906 to 0.209 in.)
      m -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) n 2.3 to 5.3 mm (0.0906 to 0.209 in.)
      o -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) p 2.3 to 5.3 mm (0.0906 to 0.209 in.)
      q -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -

  6. ADJUST REAR DOOR

    A002LG9

    Note

    Make sure to turn the engine switch off when adjusting door lock strikers.


    1. Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

      SST
      09812-00010

    2. Tighten the 4 hinge bolts on the vehicle body after adjustment.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

    3. Loosen the 4 hinge bolts on the door and adjust the door position.

    4. Tighten the 4 hinge bolts on the door after adjustment.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }
    5. A002LGC

      Disengage the 4 claws and rear door lock striker cover.

    6. A002LGS

      Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.

    7. Using a brass bar and a hammer, hit the striker to adjust its position.

    8. Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

  7. INSPECT LUGGAGE COMPARTMENT DOOR


    1. Check that the clearance measurements of areas "a" through "d" are within each standard range.

      A002LFDE01
      Standard Clearance
      Area Measurement Area Measurement
      a 7.0 mm (0.276 in.) b 2.3 to 5.3 mm (0.0906 to 0.209 in.)
      c -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) d 4.0 to 8.0 mm (0.157 to 0.315 in.)

  8. ADJUST LUGGAGE COMPARTMENT DOOR

    A002L93

    1. Loosen the 4 door side hinge bolts to adjust the door horizontally and vertically.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
    2. A002LGF

      Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.

    3. Using a brass bar and a hammer, hit the striker to adjust its position.

    4. Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }