Click here

REAR DOOR REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here
  1. Click here

    REMOVE BATTERY SERVICE HOLE COVER


    1. A01ITOM

      Remove the clip and battery service hole cover.

  2. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

  4. Click here

    REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A01IOHO

      Insert a clip remover between the plate and trim board.

    2. Turn the handle counterclockwise to remove the snap ring and handle.

  5. Click here

    REMOVE REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Remove the inside handle plate.

  6. Click here

    REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    1. A01IQU5

      Using moulding remover A, detach the 3 claws and remove the bezel.

  7. Click here

    REMOVE REAR DOOR TRIM MOULDING LH


    1. A01IPQA

      Using moulding remover A, detach the 8 claws and remove the rear door trim moulding.

  8. Click here

    REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)


    1. A01IN6I

      Using moulding remover A, detach the 4 claws.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  9. Click here

    REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01IP0B

      Remove the 3 screws.

    2. Using a clip remover, detach the 10 clips.

    3. A01IOI9E01

      Pull out the rear door trim board in the direction indicated by the arrow.

      Table 1. Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade
    4. A01IRQU

      Disconnect the 2 cables from the inside handle.

    5. A01IPSA

      Detach the claw and remove the clamp.

  10. Click here

    REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A01IOXV

      Detach the 2 claws and remove the inside handle sub-assembly from the rear door trim board.

  11. Click here

    REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. A01IRRB

      Remove the 10 screws and curtain.

  12. Click here

    REMOVE REAR NO. 1 SPEAKER ASSEMBLY

    Note:

    Do not touch the cone part of the speaker.


    1. Disconnect the speaker connector.

    2. A01IN2A

      Using a drill bit with a diameter of less than 4 mm (0.157 in.), drill out the 3 rivet heads.

      CAUTION:

      Be careful as the cut rivet will be very hot.

      Note:

      Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.

    3. Continue drilling and push out the remaining rivet fragments.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.

    5. Detach the claw and remove the speaker.

  13. Click here

    REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A01IOT0

      Detach the 4 claws and remove the inner glass weatherstrip.

  14. Click here

    REMOVE REAR DOOR INSIDE PANEL REINFORCE SUB-ASSEMBLY LH


    1. A01IMXU

      Remove the 2 bolts, 2 screws and rear door inside panel reinforce sub-assembly.

    2. Remove the rear lower door hole cover from the rear door inside panel reinforce sub-assembly.

  15. Click here

    REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A01IO5U

      Disconnect the connector.

    2. A01IT7B

      Remove the service hole cover.

      Tip:

      Remove the remaining tape on the door.

  16. Click here

    REMOVE REAR DOOR GLASS RUN LH


    1. A01IS5C

      Remove the rear door glass run.

  17. Click here

    REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)


    1. A01IP9N

      Remove the 2 curtain hooks.

  18. Click here

    REMOVE REAR DOOR FRAME GARNISH LH


    1. A01INU9

      Detach the clip and remove the rear door frame garnish.

  19. Click here

    REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. w/ Power Window:


      1. Temporarily install the regulator switch assembly.

      2. Connect the cable to the negative (-) battery terminal.

      3. Operate the regulator switch until the regulator reaches its bottom dead center.

      4. Disconnect the cable from the negative (-) battery terminal.

        Note:

        When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

      5. Remove the regulator switch assembly.

    2. w/o Power Window:


      1. Temporarily install the rear door window regulator handle assembly.

      2. Turn the handle until the regulator reaches its bottom dead center.

      3. Remove the rear door window regulator handle assembly.

    3. A01ISN0

      Remove the screw.

    4. Remove the 2 bolts and rear door window division bar sub-assembly.

  20. Click here

    REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A01IOC0

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  21. Click here

    REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH


    1. A01IQ6U

      Remove the rear door quarter window weatherstrip from the rear door quarter window glass.

  22. Click here

    REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A01INDA

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note:

      Do not damage the door glass.

  23. Click here

    REMOVE REAR DOOR GLASS CHANNEL FILLER


    1. A01IR2T

      Using a screwdriver, remove the glass channel.

      Note:

      Be careful not to damage the glass.

    2. Remove the glass channel filler from the glass channel.

  24. Click here

    REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH


    1. Put protective tape around the rear door belt moulding.

    2. Detach the 8 claws and remove the rear door belt moulding.

      Tip:

      If either of the claws labeled A are damaged, replace the rear door belt moulding with a new rear door belt moulding.

      Table 2. Text in Illustration
      *1 Protective Tape
      *2 Claw A
  25. Click here

    REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. w/ Power Window:


      1. A01IQMLE01

        Disconnect the connector.

      2. Loosen the temporary bolt.

        Table 3. Text in Illustration
        *1 Temporary Bolt
        Note:

        Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.

      3. Remove the 3 bolts.

      4. Remove the rear door window regulator assembly.

      5. Remove the temporary bolt from the rear door window regulator.

    2. A01ISQG

      w/o Power Window:

      Remove the 3 bolts and regulator.

      Note:

      Be careful when removing the bolts as the regulator may fall and become damaged.

  26. Click here

    REMOVE REAR DOOR LOCK ASSEMBLY LH


    1. A01ISCSE01

      Using a T30 "TORX" wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward, pull the release plate out of the rear door outside handle frame, and remove the rear door lock assembly and cables as a unit.

    3. Remove the door lock wiring harness seal from the rear door lock assembly.

  27. Click here

    REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A01IUHXE01

      Using a screwdriver, detach the claw.

      Tip:

      Tape the screwdriver tip before use.

    2. A01IS8IE01

      Remove the rear door remote control cable.

  28. Click here

    REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A01ISH1E01

      Using a screwdriver, detach the 3 claws.

      Tip:

      Tape the screwdriver tip before use.

    2. A01IU92E01

      Remove the rear door inside locking cable.

  29. Click here

    REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    1. A01IU6D

      Using a T30 ''TORX'' socket, loosen the screw and detach the claw to remove the outside handle cover.

  30. Click here

    REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A01IUDUE01

      Detach the holder as shown in the illustration.

      Table 4. Text in Illustration
      *1 Holder
    2. A01IR4G

      Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

  31. Click here

    REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. A01IOG7

      Detach the 3 claws and remove the pad.

  32. Click here

    REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. A01IUD6

      Detach the 2 claws and remove the pad.

  33. Click here

    REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A01IUH5

      Using a T30 ''TORX'' socket, loosen the screw.

    2. Slide the outside handle frame to remove it.

      Tip:

      Remove the outside handle frame through the service hole.

  34. Click here

    REMOVE NO. 3 SEPARATION DOOR STIFFENER CUSHION


    1. A01IS0J

      Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 3 separation door stiffener cushion.

  35. Click here

    REMOVE REAR DOOR CHECK ASSEMBLY LH


    1. A01ISY0

      Remove the bolt, 2 nuts and door check.

      Tip:

      Remove the door check through the service hole.

      Note:

      Be careful when removing the bolt and nuts as the door check may fall and become damaged.

  36. Click here

    REMOVE REAR DOOR WEATHERSTRIP LH


    1. A01IOIX

      Detach the 18 clips and remove the rear door weatherstrip.

  37. Click here

    REMOVE NO. 3 BLACK OUT TAPE LH


    1. Heat the vehicle body surface and black out tape using a heat light.

    2. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.

  38. Click here

    REMOVE NO. 4 BLACK OUT TAPE LH


    1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.