HOOD LOCK CONTROL CABLE ASSEMBLY REMOVAL

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE BATTERY SERVICE HOLE COVER


    1. A01ITOM

      Remove the clip and battery service hole cover.

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE RADIATOR SUPPORT OPENING COVER


    1. A01IRWC

      Remove the 5 clips and radiator support opening cover.

  5. REMOVE FRONT FENDER LINER LH


    1. Remove the front fender liner Click here.

  6. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A01IR0Y

    1. Remove the 2 screws <A>.

    2. Detach the claw and guide, and remove the No. 1 instrument panel under cover.

  7. REMOVE NO. 1 WATER HOSE CLAMP BRACKET

    A01IP24

    1. Remove the 2 bolts, detach the 2 claws and remove the hose clamp bracket.

  8. REMOVE HOOD LOCK ASSEMBLY


    1. for LHD:


      1. A01IS1Z

        Remove the 3 bolts and hood lock.

      2. A01IO2N

        Disconnect the hood lock control cable.

    2. for RHD:


      1. A01ITHB

        Remove the 3 bolts and hood lock.

      2. Disconnect the connector.

      3. A01IQR4

        Disconnect the hood lock control cable.

  9. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01IRIO

      Detach the 3 claws.

    2. Disconnect the hood lock control cable and remove the hood lock control lever.

  10. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. A01INSCE02
      Text in Illustration
      *1 String

      Tie a string to the end of the hood lock control cable assembly as shown in the illustration.

      Note

      Use a length of string long enough to pass through the engine compartment.

    2. Using a screwdriver, disconnect the clamps shown in the illustration.

      A01IO9WE01
      Text in Illustration
      *1 Hood Lock Control Cable Assembly *2 Clamp
      *3 Radiator Support Side *4 Headlight
      *5 Wire Harness *6 Wire Harness Clamp
      *7 Dash Panel *8 Grommet
      *9 Hood Lock Control Cable Clamp - -

      Tech Tips

      Tape the screwdriver tip before use.

    3. Pull the cable out of the wheel housing from outside of the vehicle, and then untie the string and remove the cable.

  11. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. A01INSCE02
      Text in Illustration
      *1 String

      Tie a string to the end of the hood lock control cable assembly as shown in the illustration.

      Note

      Use a length of string long enough to pass through the engine compartment.

    2. Using a screwdriver, disconnect the clamps shown in the illustration.

      A01IMZ1E01
      Text in Illustration
      *1 Hood Lock Control Cable Assembly *2 Clamp
      *3 Radiator Support Side *4 Headlight
      *5 Wire Harness *6 Wire Harness Clamp
      *7 Dash Panel *8 Grommet
      *9 Hood Lock Control Cable Clamp *10 Radiator Hose
      *11 Washer Hose *12 Washer Hose Clamp

      Tech Tips

      Tape the screwdriver tip before use.

    3. Pull the cable out of the wheel housing from outside of the vehicle, and then untie the string and remove the cable.