ROOF HEADLINING INSTALLATION

INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER LH (w/ Rear No. 1 Seat, w/ Rear No. 2 Seat)

1. Attach the claw and guide to install the rear No. 2 seat shoulder belt hanger.

INSTALL REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 1 Seat)

1. Attach the claw and guide to install the rear seat shoulder belt hanger.

INSTALL NO. 1 ROOF SIDE INNER GARNISH CAP (w/o Rear No. 1 Seat, w/o Rear No. 2 Seat)

1. Attach the 2 claws to install the No. 1 roof side inner garnish cap.

INSTALL REAR DECK TRIM CLIP (w/o Rear No. 1 Seat)

1. Attach the claw and guide to install the rear deck trim clip.

INSTALL DECK SIDE TRIM COVER LH (w/o Rear No. 2 Seat)

1. Install the deck side trim cover with the 2 screws.

INSTALL NO. 1 CUP HOLDER

1. Attach the 3 claws and 2 guides to install the No. 1 cup holder.

INSTALL DECK TRIM SIDE BELT HOLE COVER LH (w/o Rear No. 2 Seat)

1. Slide the deck trim side belt hole cover in the direction indicated by the arrow in the illustration and attach the 2 claws and 6 guides to install it.

INSTALL NO. 1 DECK BOARD BRACKET LH (w/o Rear No. 2 Seat)

1. Install the No. 1 deck board bracket with the 2 screws.

INSTALL REAR NO. 3 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

1. Attach the 2 claws to install the rear No. 3 side rail spacer.

INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Rear No. 2 Seat, w/o Curtain Shield Airbag)

1. Attach the 2 claws to install the rear No. 2 side rail spacer.

INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

1. Attach the 4 claws to install the rear side rail spacer.

INSTALL FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

1. Attach the 4 claws to install the front side rail spacer.

INSTALL SHOULDER BELT ANCHOR PLATE LH

1. Attach the 5 claws and 3 guides to install the shoulder belt anchor plate.

INSTALL REAR DOOR SCUFF PANEL LH

1. Attach the 5 claws and guide to install the rear door scuff panel.

INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

1. Attach the 3 clips and 2 guides to install the rear door scuff plate outside.

INSTALL FRONT DOOR SCUFF PLATE OUTSIDE

1. Attach the 3 clips and 2 guides to install the front door scuff plate outside.

INSTALL ROOF HEADLINING ASSEMBLY

1. 

   Place the roof headlining into the vehicle through the back door.

   Note:

   Be careful not to damage the roof headlining when placing it in the cabin.

2. w/o Roof Sunshade System:

   
   
   1. 

      Install the roof headlining with the 6 clips.

3. w/ Roof Sunshade System:

   
   

   1. Attach the 2 guides and 11 fasteners to install the headlining.

   2. 

      Install the 3 clips.

      Table 1. Text in Illustration

      *1

      Guide

      *2

      Fastener

4. for LHD:

   
   
   1. 

      Connect the 2 connectors and attach the 2 clamps.

5. for RHD:

   
   
   1. 

      Connect the connector.

   2. 

      Connect the connector and attach the 2 clamps.

6. 

   Attach the 4 clamps to the front pillar LH.

7. 

   Connect the 2 connectors and attach the clamp to the rear pillar RH.

8. Install the bolt, and then align the No. 2 antenna cord with the cutout in the roof headlining and install the No. 2 antenna cord to the roof headlining.

   Table 2. Text in Illustration

   *1	Roof Headlining Cutout

9. 

   Connect the connector and attach the 3 clamps to the front pillar RH.

10. 

    w/ Rain Sensor:

    Connect the rain sensor connector.

11. 

    w/ EC Mirror:

    Connect the EC mirror connector.

INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

1. Attach the 2 hinges to install the glove compartment door.

2. 

   Attach the glove compartment door stopper to the glove compartment door as shown in the illustration.

3. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the glove compartment door to engage the 2 stoppers.

   Table 3. Text in Illustration

   *1

   Stopper

INSTALL REAR ASSIST GRIP ASSEMBLY

1. Assemble the rear assist grip as shown in the illustration.

2. 

   Install the rear assist grip.

INSTALL ASSIST GRIP ASSEMBLY

1. Assemble the assist grip as shown in the illustration.

2. 

   Install the assist grip.

INSTALL VISOR HOLDER

1. Attach the 2 claws.

2. Push in the visor holder as shown in the illustration.

INSTALL VISOR ASSEMBLY LH

1. Attach the 2 clips to install the visor.

INSTALL SEAT BELT ANCHOR COVER

1. Attach the 2 claws to install the seat belt anchor cover.

2. Install the 2 screws.

INSTALL MAP LIGHT ASSEMBLY

1. Connect the connector.

2. Attach the 4 clips to install the map light.

INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH

1. Attach the 7 clips to install the inner roof side garnish.

2. w/ Rear No. 1 Seat:

   
   
   1. 

      Install the rear No. 1 seat belt shoulder anchor with the bolt.

      41 N*m

      418 kgf*cm

      30 ft.*lbf

   2. 

      Attach the 2 claws to close the rear No. 1 seat belt shoulder anchor cover.

3. w/ Rear No. 2 Seat:

   
   
   1. 

      Install the rear No. 2 seat belt shoulder anchor with the bolt.

      42 N*m

      428 kgf*cm

      31 ft.*lbf

   2. 

      Attach the 2 claws to close the rear No. 2 seat belt shoulder anchor cover.

INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

1. Install the luggage hold belt striker with the bolt.

INSTALL DECK TRIM SIDE SERVICE HOLE COVER

1. Attach the 4 claws and 2 guides to install the deck trim side service hole cover.

INSTALL FRONT DECK SIDE TRIM COVER LH

1. Attach the 2 claws to install the front deck side trim cover.

INSTALL CENTER PILLAR GARNISH LH

1. Pass the front seat outer belt floor anchor through the center pillar garnish.

2. Attach the clip to install the center pillar garnish.

3. Install the 2 screws.

4. 

   Install the front seat outer belt floor anchor with the bolt.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

INSTALL LAP BELT OUTER ANCHOR COVER

1. Attach the 3 claws to install the lap belt outer anchor cover.

INSTALL LOWER CENTER PILLAR GARNISH LH

1. Attach the 2 claws and 2 clips to install the lower center pillar garnish.

INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

1. Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the weatherstrip as shown in the illustration.

   Table 4. Text in Illustration

   *1	Paint Mark
   *2	Mark Position

INSTALL REAR DOOR SCUFF PLATE LH

1. Attach the 9 claws and 2 clips to install the rear door scuff plate.

INSTALL FRONT PILLAR GARNISH LH

1. Remove the protective cover.

2. Attach the 2 claws.

3. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.

   Tip:

   Tape the tips of the needle-nose pliers before use.

   Table 5. Text in Illustration

   *1	Front Pillar Garnish Clip
   *2	Protective Tape

4. 

   Attach the 2 clips to install the front pillar garnish.

   *1	Front Pillar Garnish Clip

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

1. Align the paint mark on the front door opening trim weatherstrip with the mark position on the vehicle and install the weatherstrip as shown in the illustration.

   Table 6. Text in Illustration

   *1	Paint Mark
   *2	Mark Position

INSTALL COWL SIDE TRIM BOARD LH

1. Attach the 2 clips and guide to install the cowl side trim board.

INSTALL FRONT DOOR SCUFF PLATE LH

1. Attach the 8 claws and 2 clips to install the front door scuff plate.

INSTALL REAR DECK TRIM COVER

1. Attach the 6 claws and 4 guides to install the rear deck trim cover.

INSTALL DECK TRIM SIDE BELT HOLE COVER LH (w/ Rear No. 2 Seat)

1. Slide the deck trim side belt hole cover in the direction indicated by the arrow in the illustration and attach the 2 claws and 6 guides to install it.

INSTALL DECK FLOOR BOX LH

1. w/o Rear No. 2 Seat:

   
   

   1. Attach the 4 claws to install the deck floor box.

2. 

   w/ Rear No. 2 Seat:

   
   

   1. Attach the 3 claws and guide to install the deck floor box.

   2. Install the bolt.

INSTALL DECK FLOOR BOX RH

1. w/o Rear No. 2 Seat:

   
   

   1. Attach the 2 claws and guide to install the deck floor box.

2. 

   w/ Rear No. 2 Seat:

   
   

   1. Attach the 2 claws and guide to install the deck floor box.

   2. Install the bolt.

INSTALL LOWER DECK TRIM SIDE BOARD LH (w/o Rear No. 2 Seat)

1. Attach the claw and 2 guides to install the lower deck trim side board.

INSTALL DECK RAIL COVER (w/ Rear No. 2 Seat, w/o Spare Tire)

1. Attach the 2 claws and 2 guides to install the deck rail cover.

2. Install the clip.

INSTALL LUGGAGE COMPARTMENT TRAY (w/ Rear No. 2 Seat, w/ Spare Tire)

1. Install the luggage compartment tray.

INSTALL FRONT DECK FLOOR BOX (w/o Rear No. 2 Seat)

1. Install the front deck floor box with the 3 bolts.

INSTALL DECK BOARD ASSEMBLY (w/ Rear No. 2 Seat)

1. Attach the 4 claws and 6 clips to install the deck board.

INSTALL NO. 2 DECK BOARD (w/o Rear No. 2 Seat)

1. Attach the 5 clips to install the No. 2 deck board.

INSTALL NO. 1 DECK BOARD (w/o Rear No. 2 Seat)

1. Install the No. 1 deck board.

INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

1. Install the tonneau cover.