ROOF HEADLINING REMOVAL


  1. REMOVE BATTERY SERVICE HOLE COVER


    1. A01ITOM

      Remove the clip and battery service hole cover.

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A01IUDC

    1. Remove the tonneau cover.

  5. REMOVE NO. 1 DECK BOARD (w/o Rear No. 2 Seat)

    A01IO5W

    1. Remove the No. 1 deck board.

  6. REMOVE NO. 2 DECK BOARD (w/o Rear No. 2 Seat)

    A01IUJ6

    1. Detach the 5 clips and remove the No. 2 deck board.

  7. REMOVE DECK BOARD ASSEMBLY (w/ Rear No. 2 Seat)

    A01IRW6

    1. Detach the 4 claws and 6 clips, and remove the deck board.

  8. REMOVE FRONT DECK FLOOR BOX (w/o Rear No. 2 Seat)

    A01INUT

    1. Remove the 3 bolts and front deck floor box.

  9. REMOVE LUGGAGE COMPARTMENT TRAY (w/ Rear No. 2 Seat, w/ Spare Tire)

    A01ISB5

    1. Remove the luggage compartment tray.

  10. REMOVE DECK RAIL COVER (w/ Rear No. 2 Seat, w/o Spare Tire)

    A01IP10

    1. Remove the clip.

    2. Detach the 2 claws and 2 guides, and remove the deck rail cover.

  11. REMOVE LOWER DECK TRIM SIDE BOARD LH (w/o Rear No. 2 Seat)

    A01IN88

    1. Detach the claw and 2 guides, and remove the lower deck trim side board.

  12. REMOVE LOWER DECK TRIM SIDE BOARD RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE DECK FLOOR BOX LH

    A01IU1X

    1. w/o Rear No. 2 Seat:


      1. Detach the 4 claws and remove the deck floor box.

    2. A01IN2Q

      w/ Rear No. 2 Seat:


      1. Remove the bolt.

      2. Detach the 3 claws and guide, and remove the deck floor box.

  14. REMOVE DECK FLOOR BOX RH

    A01ISZR

    1. w/o Rear No. 2 Seat:


      1. Detach the 2 claws and guide, and remove the deck floor box.

    2. A01IPFF

      w/ Rear No. 2 Seat:


      1. Remove the bolt.

      2. Detach the 2 claws and guide, and remove the deck floor box.

  15. REMOVE DECK TRIM SIDE BELT HOLE COVER LH (w/ Rear No. 2 Seat)

    A01IUQX

    1. Detach the 2 claws and 6 guides, and remove the deck trim side belt hole cover in the direction indicated by the arrow in the illustration.

  16. REMOVE DECK TRIM SIDE BELT HOLE COVER RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE REAR NO. 2 SEAT TRACK BRACKET COVER (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure to remove the cover on the other side.


    1. A01IS71

      Detach the 2 claws and remove the cover.

  18. REMOVE REAR NO. 2 SEAT TRACK COVER (w/ Rear No. 2 Seat)


    1. A01IPIR

      Detach the 3 claws and 2 guides, and then remove the cover.

  19. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. Disconnect the connector under the seat.

    2. Remove the 5 bolts.

      A01IRCI

    3. Pull the 2 straps and fold down the 2 seatbacks.

      A01ITYW

    4. Remove the 2 bolts.

    5. Remove the rear No. 2 seat assembly from the vehicle.

      Note

      Be careful not to damage the vehicle body.

  20. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. Remove the rear deck floor box.

      A01IO7TE01

  21. REMOVE REAR DECK TRIM COVER

    A01ITUG

    1. Detach the 6 claws and 4 guides, and remove the rear deck trim cover.

  22. REMOVE FRONT DOOR SCUFF PLATE LH

    A01IPG9

    1. Detach the 8 claws and 2 clips, and remove the front door scuff plate.

  23. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE COWL SIDE TRIM BOARD LH

    A01ISRD

    1. Detach the 2 clips and guide, and remove the cowl side trim board.

  25. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A01INM0

    1. Remove the front door opening trim weatherstrip.

  27. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE FRONT PILLAR GARNISH LH

    A01IURGE01
    Text in Illustration
    *1 Front Pillar Garnish Clip

    1. Pull the upper part of the garnish toward the inside of the cabin and detach the 2 clips.

      Tech Tips

      Allow the front pillar garnish to hang by the front pillar garnish clip.

    2. A01ISK0E01
      Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

      Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the tips of the needle-nose pliers before use.

    3. Detach the 2 claws and remove the front pillar garnish.

    4. A01IR1KE01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  29. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE REAR DOOR SCUFF PLATE LH

    A01IQ4G

    1. Detach the 9 claws and 2 clips, and remove the rear door scuff plate.

  31. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A01ISHX

    1. Remove the rear door opening trim weatherstrip.

  33. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. REMOVE LOWER CENTER PILLAR GARNISH LH

    A01IUA8

    1. Detach the 2 claws and 2 clips, and remove the lower center pillar garnish.

  35. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE NO. 2 FLOOR BOARD


    1. Remove the No. 2 floor board.

  37. REMOVE NO. 1 FLOOR BOARD


    1. Remove the No. 1 floor board.

  38. REMOVE LAP BELT OUTER ANCHOR COVER

    A01IOX0

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Detach the 3 claws and remove the lap belt outer anchor cover.

  39. REMOVE CENTER PILLAR GARNISH LH

    A01IS1B

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A01IO55

      Remove the 2 screws.

    3. Detach the clip.

    4. Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.

  40. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  41. REMOVE FRONT DECK SIDE TRIM COVER LH

    A01ING9E01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  42. REMOVE FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  43. REMOVE DECK TRIM SIDE SERVICE HOLE COVER

    A01IUGKE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure to remove the deck trim side service hole cover on the other side.


    1. Using a screwdriver, detach the 4 claws and 2 guides, and remove the deck trim side service hole cover.

      Tech Tips

      Tape the screwdriver tip before use.

  44. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

    A01IUD8

    Tech Tips

    Use the same procedure for all the luggage hold belt strikers.


    1. Remove the bolt and luggage hold belt striker.

  45. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    A01IULD

    1. w/ Rear No. 1 Seat:

      Remove the bolt and rear No. 1 seat belt anchor.

    2. A01IRRR

      w/ Rear No. 2 Seat:

      Remove the bolt and rear No. 2 seat belt anchor

    3. Remove the 2 bolts.

    4. Detach the 6 clips and 7 claws.

    5. Disconnect the connector and remove the deck trim side panel.

      A01ISVL

  46. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    A01IQEC

    1. w/ Rear No. 1 Seat:

      Remove the bolt and rear No. 1 seat belt anchor.

    2. A01IPQ5

      w/ Rear No. 2 Seat:

      Remove the bolt and rear No. 2 seat belt anchor.

    3. Remove the 2 bolts.

    4. Detach the 6 clips and 7 claws, and remove the deck trim side panel.

      A01ISDV

  47. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH


    1. w/ Rear No. 1 Seat:


      1. A01IRBT

        Using a moulding remover, detach the 2 claws and open the rear No. 1 seat belt shoulder anchor cover.

      2. A01IQVY

        Remove the bolt and rear No. 1 seat belt shoulder anchor.

    2. w/ Rear No. 2 Seat:


      1. A01ISCE

        Using a moulding remover, detach the 2 claws and open the rear No. 2 seat belt shoulder anchor cover.

      2. A01IRKY

        Remove the bolt and rear No. 2 seat belt shoulder anchor.

    3. A01IRBL

      Detach the 7 clips and remove the inner roof side garnish.

  48. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  49. REMOVE MAP LIGHT ASSEMBLY

    A01ITZH

    1. Using a moulding remover, detach the 4 clips.

    2. Disconnect the connector and remove the map light.

  50. REMOVE SEAT BELT ANCHOR COVER

    A01ISBX

    1. Remove the 2 screws.

    2. Detach the 2 claws and remove the seat belt anchor cover.

  51. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A01IU7CE01

      Detach the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.

    2. A01IPI6

      Detach the 6 claws and remove the inner rear view mirror stay holder cover.

  52. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A01IPUT

      Using moulding remover A, detach the 3 claws and disconnect the rain sensor cover.

    2. A01IOSH

      Detach the 2 claws and remove the rain sensor cover.

  53. REMOVE VISOR ASSEMBLY LH

    A01ISS2

    1. Using a moulding remover, detach the 2 clips and remove the visor.

  54. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  55. REMOVE VISOR HOLDER

    A01IN9HE01

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  56. REMOVE ASSIST GRIP ASSEMBLY

    A01IST9E02

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry the assist grip plugs as shown in the illustration to detach the claws.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape

    2. Pull off the 2 assist grip plugs by hand.

    3. A01IT3X

      Detach the 2 clips and remove the assist grip.

    4. Remove the 2 clips from the vehicle body.

  57. REMOVE REAR ASSIST GRIP ASSEMBLY

    A01IQV5E02

    Tech Tips

    Use the same procedure for the other rear assist grip.


    1. Using a clip remover, detach the 4 claws.

      Note

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      Tech Tips


      • Gently pry the assist grip plugs as shown in the illustration to detach the claws.

      • Tape the clip remover tip before use.

      Text in Illustration
      *1 Protective Tape

    2. Pull off the 2 assist grip plugs by hand.

    3. A01ITVJ

      Detach the 2 clips and remove the rear assist grip.

    4. Remove the 2 clips from the vehicle body.

  58. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Remove the instrument panel safety pad sub-assembly Click here.

  59. REMOVE FUSE BOX OPENING COVER (for LHD)

    A01IO2H

    1. for LHD:


      1. Detach the 6 clips and 4 claws.

      2. Disconnect the connectors and remove the fuse box opening cover.

    2. for RHD:


      1. Detach the 5 clips and 4 claws.

      2. Disconnect the connectors and remove the fuse box opening cover.

        A01IU2PE01

  60. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

    A01IOKA

    1. Push in the sides of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.

    2. Detach the glove compartment door stopper from the glove compartment door as shown in the illustration.

    3. A01ISTC

      Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.

  61. REMOVE ROOF HEADLINING ASSEMBLY

    A01ITZT

    Tech Tips

    Before removing the roof headlining, move the front seats and rear No. 1 seat to the positions shown in the illustration.


    1. A01IRIH

      w/ EC Mirror:

      Disconnect the EC mirror connector.

    2. A01IUOR

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A01ITMM

      Disconnect the connector and detach the 3 clamps from the front pillar RH.

    4. A01IU82

      Remove the bolt.

    5. Disconnect the 2 connectors and detach the clamp from the rear pillar RH.

    6. A01IOUI

      Detach the 4 clamps from the front pillar LH.

    7. for LHD:


      1. A01IS4L

        Disconnect the 2 connectors and detach the 2 clamps.

    8. for RHD:


      1. A01IROG

        Disconnect the connector and detach the 2 clamps.

      2. A01IROK

        Disconnect the connector.

    9. w/o Roof Sunshade System:


      1. Remove the 6 clips.

        A01IRZG

    10. w/ Roof Sunshade System:


      1. Remove the 3 clips.

      2. Detach the 2 guides and 11 fasteners.

        A01IRQ8E01
        Text in Illustration
        *1 Guide *2 Fastener
    11. A01IOZ0

      Remove the roof headlining from the back door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when taking it out.

  62. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE

    A01ITDBE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure to remove the front door scuff plate outside on the other side.


    1. Put protective tape around the front door scuff plate outside.

    2. Using a moulding remover, detach the 3 clips and 2 guides, and remove the front door scuff plate outside.

  63. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    A01IPY6E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate outside.

    2. Using a moulding remover, detach the 3 clips and 2 guides, and remove the rear door scuff plate outside.

  64. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedure described for the LH side.

  65. REMOVE REAR DOOR SCUFF PANEL LH

    A01IRIX

    1. Detach the 5 claws and guide, and remove the rear door scuff panel.

  66. REMOVE REAR DOOR SCUFF PANEL RH

    Tech Tips

    Use the same procedure described for the LH side.

  67. REMOVE SHOULDER BELT ANCHOR PLATE LH

    A01IQ75

    1. Detach the 5 claws and 3 guides, and remove the shoulder belt anchor plate.

  68. REMOVE SHOULDER BELT ANCHOR PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  69. REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A01IPI3

    1. Detach the 4 claws and remove the front side rail spacer.

  70. REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  71. REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    A01IT2P

    1. Detach the 4 claws and remove the rear side rail spacer.

  72. REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  73. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Rear No. 2 Seat, w/o Curtain Shield Airbag)

    A01ITHF

    1. Detach the 2 claws and remove the rear No. 2 side rail spacer.

  74. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Rear No. 2 Seat, w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  75. REMOVE REAR NO. 3 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

    A01ISOU

    1. Detach the 2 claws and remove the rear No. 3 side rail spacer.

  76. REMOVE REAR NO. 3 SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  77. REMOVE NO. 1 DECK BOARD BRACKET LH (w/o Rear No. 2 Seat)

    A01IQC8

    1. Remove the 2 screws and No. 1 deck board bracket.

  78. REMOVE NO. 1 DECK BOARD BRACKET RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  79. REMOVE DECK TRIM SIDE BELT HOLE COVER LH (w/o Rear No. 2 Seat)

    A01IN6G

    1. Detach the 2 claws and 6 guides, and remove the deck trim side belt hole cover in the direction indicated by the arrow in the illustration.

  80. REMOVE DECK TRIM SIDE BELT HOLE COVER RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  81. REMOVE NO. 1 CUP HOLDER

    A01IQS6

    Tech Tips

    Use the same procedure to remove the No. 1 cup holder on the other side.


    1. Detach the 3 claws and 2 guides, and remove the No. 1 cup holder.

  82. REMOVE DECK SIDE TRIM COVER LH (w/o Rear No. 2 Seat)

    A01IQRY

    1. Remove the 2 screws and deck side trim cover.

  83. REMOVE DECK SIDE TRIM COVER RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  84. REMOVE REAR DECK TRIM CLIP (w/o Rear No. 1 Seat)

    A01IOOU

    Tech Tips

    Use the same procedure to remove the rear deck trim clip on the other side.


    1. Detach the claw and guide, and remove the rear deck trim clip.

  85. REMOVE NO. 1 ROOF SIDE INNER GARNISH CAP (w/o Rear No. 1 Seat, w/o Rear No. 2 Seat)

    A01IRBC

    Tech Tips

    Use the same procedure for all the No. 1 roof side inner garnish caps.


    1. Detach the 2 claws and remove the No. 1 roof side inner garnish cap.

  86. REMOVE REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 1 Seat)

    A01ITMB

    1. Detach the claw and guide, and remove the rear seat shoulder belt hanger.

  87. REMOVE REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 1 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  88. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH (w/ Rear No. 1 Seat, w/ Rear No. 2 Seat)

    A01ITMB

    1. Detach the claw and guide, and remove the rear No. 2 seat shoulder belt hanger.

  89. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH (w/ Rear No. 1 Seat, w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.