Click here

UPPER INSTRUMENT PANEL INSTALLATION

Click here
Click here Click here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here
  1. Click here

    INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Securely attach the 5 guides, 4 claws and 2 clips of the instrument panel safety pad to the vehicle body.

    2. A01ISGS

      Install the instrument panel safety pad with the 3 screws <B>.

    3. Install the passenger airbag bolt <A>.

      20 N*m 204 kgf*cm 15 ft.*lbf
    4. A01IOAC

      Connect the connector and clamps.

  2. Click here

    INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. for 4 Speakers:


      1. Set the 2 claws on the side of the No. 1 instrument panel speaker panel towards the front of the vehicle in place and using them as pivot points, lower the No. 1 instrument panel speaker panel in the direction indicated by the arrow in the illustration, and then attach the claws and clips to the instrument panel to install the No. 1 instrument panel speaker panel.

    2. A01IREG

      for 6 Speakers:


      1. Connect the speaker connector.

      2. A01IRJ2

        Set the 2 claws on the side of the No. 1 instrument panel speaker panel towards the front of the vehicle in place and using them as pivot points, lower the No. 1 instrument panel speaker panel in the direction indicated by the arrow in the illustration, and then attach the claws and clips to the instrument panel to install the No. 1 instrument panel speaker panel.

  3. Click here

    INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Tip:

    Use the same procedure described for the No. 1 instrument panel speaker panel.

  4. Click here

    INSTALL NO. 1 SWITCH HOLE BASE


    1. w/ Entry and Start System:


      1. Connect the connector.

      2. Attach the 2 claws and 2 clips to install the No. 1 switch hole base.

    2. A01ISBI

      w/o Entry and Start System:


      1. Attach the 2 claws and 2 clips to install the No. 1 switch hole base.

  5. Click here

    INSTALL NO. 2 SWITCH HOLE BASE


    1. for LHD:

      Attach the 5 claws and 5 clips to install the No. 2 switch hole base.

    2. A01IQ8G

      for RHD:

      Attach the 3 claws and 5 clips to install the No. 2 switch hole base.

  6. Click here

    INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle)


    1. for Automatic Air Conditioning System:


      1. Attach the 2 claws, 4 clips and 5 guides to install the lower center instrument panel finish panel.

      2. Install the 2 screws <C>.

    2. A01IQS2

      for Manual Air Conditioning System:


      1. Attach the 4 clips, 2 claws and 5 guides to install the lower center instrument panel finish panel.

      2. Install the 2 screws <C>.

  7. Click here

    INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (except Manual Transaxle)


    1. for Automatic Air Conditioning System:


      1. Attach the 2 claws, 4 clips and 5 guides to install the lower center instrument panel finish panel.

      2. Install the 3 screws <C>.

    2. A01IQNM

      for Manual Air Conditioning System:


      1. Attach the 4 clips, 2 claws and 5 guides to install the lower center instrument panel finish panel.

      2. Install the 3 screws <C>.

  8. Click here

    INSTALL SHIFTING HOLE COVER (for Manual Transaxle)


    1. Attach the 5 claws and 3 clips to install the shifting hole cover.

    2. Install the knob spring.

    3. Install the T washer and twist it in the direction indicated by the arrow.

      Table 1. Text in Illustration
      *1 T Washer
  9. Click here

    INSTALL POSITION INDICATOR HOUSING ASSEMBLY (except Manual Transaxle)


    1. Connect the connector.

    2. Attach the 5 claws and 3 clips to install the position indicator housing.

  10. Click here

    INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01IQX6E01

      Install the shift lever knob and twist it in the direction indicated by the arrow.

  11. Click here

    INSTALL STEREO OPENING COVER WITH BRACKET (w/o Audio)


    1. Install the stereo opening cover with the 4 bolts.

  12. Click here

    INSTALL RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)


    1. Connect the connectors.

    2. A01IN8Y

      Insert the radio receiver assembly with bracket to attach the 4 clips on its backside.

      Note:

      When inserting the radio receiver, do not press the knobs on it.

    3. Install the radio receiver assembly with bracket with the 4 screws.

      4.0 N*m 40 kgf*cm 35 in.*lbf
  13. Click here

    INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


    1. Connect the connectors.

    2. A01ITIX

      Insert the radio and display receiver assembly with bracket to attach the 4 clips on its backside.

      Note:

      When inserting the radio and display receiver, do not press the knobs on it.

    3. Install the radio and display receiver assembly with bracket with the 4 screws.

      4.0 N*m 40 kgf*cm 35 in.*lbf
  14. Click here

    INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Audio, for Radio and Display Type)


    1. Attach the 4 clips, 3 claws and 3 guides to install the center instrument cluster finish panel.

  15. Click here

    INSTALL COMBINATION METER ASSEMBLY


    1. A01INN0

      Connect the connector.

    2. Attach the clamp.

    3. A01INRI

      Attach the clip to install the combination meter.

    4. Install the 2 screws.

  16. Click here

    INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. Attach the 11 guides and 4 claws to install the instrument cluster finish panel.

  17. Click here

    INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Connect the connector.

    2. Attach the 8 claws and 4 guides to install the center instrument panel register.

  18. Click here

    INSTALL INSTRUMENT PANEL FINISH PANEL END RH


    1. for Automatic Air Conditioning System:

      Attach the 3 clips, claw and 2 guides to install the instrument panel finish panel end RH.

    2. A01ISYI

      for Manual Air Conditioning System:

      Attach the 3 clips, claw and guide to install the instrument panel finish panel end RH.

  19. Click here

    INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. A01IPRP

      for Automatic Air Conditioning System:

      Attach the 3 clips and 2 guides to install the instrument panel finish panel end LH.

    2. A01IOHW

      for Manual Air Conditioning System:

      Attach the 3 clips and guide to install the instrument panel finish panel end LH.

  20. Click here

    INSTALL GLOVE COMPARTMENT DOOR SUB-ASSEMBLY


    1. Connect the connector.

    2. Attach the 7 claws and 5 guides to install the glove compartment door.

    3. Install the 2 screws.

  21. Click here

    INSTALL FRONT PILLAR GARNISH LH


    1. Remove the protective cover.

    2. Attach the 2 claws.

    3. Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.

      Tip:

      Tape the tips of the needle-nose pliers before use.

      Table 2. Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape
    4. A01ISQBE01

      Attach the 2 clips to install the front pillar garnish.

      *1 Front Pillar Garnish Clip
  22. Click here

    INSTALL FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  23. Click here

    INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Align the paint mark on the front door opening trim weatherstrip with the mark position on the vehicle and install the weatherstrip as shown in the illustration.

      Table 3. Text in Illustration
      *1 Paint Mark
      *2 Mark Position
  24. Click here

    INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure described for the LH side.

  25. Click here

    INSTALL COWL SIDE TRIM BOARD LH


    1. Attach the 2 clips and guide to install the cowl side trim board.

  26. Click here

    INSTALL COWL SIDE TRIM BOARD RH

    Tip:

    Use the same procedure described for the LH side.

  27. Click here

    INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 8 claws and 2 clips to install the front door scuff plate.

  28. Click here

    INSTALL FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure described for the LH side.

  29. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  30. Click here

    CHECK SRS WARNING LIGHT


    1. Check the SRS warning light (Click here).