Click here

HEATER ASSEMBLY (w/ Combustion Type Power Heater) INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL HEATER WITH EXHAUST PIPE ASSEMBLY


    1. A01IPB7

      Install the heater with exhaust pipe assembly with the 3 nuts.

      7.5 N*m 77 kgf*cm 66 in.*lbf
    2. A01IO6A

      Attach the clamp.

    3. Connect the 3 hoses.

    4. Using pliers, grip the claws of the clips and slide the 3 clips.

    5. Connect the connector.

  2. Click here

    INSTALL NO. 1 EXHAUST PIPE SUB-ASSEMBLY


    1. A01IP1TE01

      Install the No. 1 exhaust pipe sub-assembly with the 2 nuts labeled <A>.

      7.5 N*m 77 kgf*cm 66 in.*lbf

    2. Install the nut labeled <B>.

      7.5 N*m 77 kgf*cm 66 in.*lbf
  3. Click here

    INSTALL AIR DUCT


    1. A01ISZ7

      Install the air duct with the clip.

  4. Click here

    INSTALL COWL TOP OUTER PANEL


    1. Install the cowl top panel with the 9 bolts.

      8.8 N*m 90 kgf*cm 78 in.*lbf
  5. Click here

    INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for DPF)


    1. A01INRQE02

      Connect the 2 vacuum hoses.

      Note:

      Connect the vacuum hoses so that the painted marks of the 2 vacuum hoses are as shown in the illustration.

    2. A01IT6Y

      Install the sensor with the bolt.

      8.0 N*m 82 kgf*cm 71 in.*lbf

    3. Connect the sensor connector and attach the wire harness clamp.

  6. Click here

    INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A01ISAD

      Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body and install the wiper motor and link.

    2. A01ITHG

      Install the 2 bolts.

      5.5 N*m 56 kgf*cm 49 in.*lbf
    3. A01IQJZ

      Connect the connector and attach the clamp to install the wire harness to the cowl top panel.

  7. Click here

    INSTALL COWL TOP VENTILATOR LOUVER LH


    1. A01IPRQ

      Attach the 6 claws and 5 guides to install the cowl top ventilator louver LH.

    2. Install the clip.

    3. A01INVH

      Attach the 2 claws and 2 guides to install the center cowl top ventilator louver.

  8. Click here

    INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01IQI1

      Attach the 4 claws and 5 guides to install the cowl top ventilator louver RH.

    2. Install the clip.

  9. Click here

    INSTALL HOOD TO COWL TOP SEAL


    1. A01IQHZ

      Attach the 7 clips and 2 claws to install the hood to cowl top seal.

  10. Click here

    INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A01ITA3E01

      Clean the wiper arm serrations.

      Table 1. Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A01ITAIE01

      Position the blade tip within the range shown in the illustration.

      Tip:

      The lower limit of the range is indicated by the mark on the glass.

      Table 2. Text in Illustration
      *1 Mark for Blade Position

    5. Install the front wiper arm and blade assembly LH with the nut.

      26 N*m 265 kgf*cm 19 ft.*lbf
      Tip:

      Hold the arm hinge by hand when tightening the nut.

    6. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

  11. Click here

    INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A01ITA3E01

      Clean the wiper arm serrations.

      Table 3. Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A01ITNDE01

      Position the blade tip within the range shown in the illustration.

      Tip:

      The lower limit of the range is indicated by the mark on the glass.

      Table 4. Text in Illustration
      *1 Mark for Blade Position

    5. Install the front wiper arm and blade assembly RH with the nut.

      26 N*m 265 kgf*cm 19 ft.*lbf
      Tip:

      Hold the arm hinge by hand when tightening the nut.

  12. Click here

    INSTALL FRONT WIPER ARM HEAD CAP


    1. A01ISR6

      Install the front wiper arm head cap.

      Tip:

      Use the same procedure for all front wiper arm head caps.

  13. Click here

    INSTALL NO. 1 ENGINE COVER


    1. A01INMI

      Attach the 4 clips to install the No. 1 engine cover.