FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

    A01INZ2

    1. Align the claw with the adjuster positioning hole and install the anchor adjuster with the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Tech Tips

      First install the lower bolt, and then install the upper bolt.

  2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

    A01IN1PE01

    Note

    When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.


    1. Align the seat outer belt positioning holes with the claws and install the retractor of the seat outer belt with the 2 bolts.

      Torque:
      for bolt A
      5.0 N*m  { 51 kgf*cm, 30 in.*lbf }
      for bolt B
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Tech Tips

      First install bolt A, and then install bolt B.

      Text in Illustration
      *1 Bolt A
      *2 Bolt B
    2. A01IT1U

      Connect the pretensioner connector as shown in the illustration.

    3. A01IP9M

      Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL CENTER PILLAR GARNISH LH

    A01IO55

    1. Pass the front seat outer belt floor anchor through the center pillar garnish.

    2. Attach the clip to install the center pillar garnish.

    3. Install the 2 screws.

    4. A01IS1B

      Install the front seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  4. INSTALL LAP BELT OUTER ANCHOR COVER

    A01IOX0

    Tech Tips

    Use the same procedure for the other lap belt outer anchor cover.


    1. Attach the 3 claws to install the lap belt outer anchor cover.

  5. INSTALL NO. 2 FLOOR BOARD


    1. Install the No. 2 floor board.

  6. INSTALL LOWER CENTER PILLAR GARNISH LH

    A01IUA8

    1. Attach the 2 claws and 2 clips to install the lower center pillar garnish.

  7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A01IP6WE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the weatherstrip as shown in the illustration.

  8. INSTALL REAR DOOR SCUFF PLATE LH

    A01IRIX

    1. Attach the 5 claws and guide to install the rear door scuff panel.

  9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A01IQCDE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the front door opening trim weatherstrip with the mark position on the vehicle and install the weatherstrip as shown in the illustration.

  10. INSTALL COWL SIDE TRIM BOARD LH

    A01ISRD

    1. Attach the 2 clips and guide to install the cowl side trim board.

  11. INSTALL FRONT DOOR SCUFF PLATE LH

    A01IPG9

    1. Attach the 8 claws and 2 clips to install the front door scuff plate.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.