FRONT SEAT CUSHION HEATER INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH


    1. A01IQN7

      Install the front seat cushion heater assembly LH to the separate type front seat cushion cover with new tack pins.

  2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01IQ2EE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  3. INSTALL SEAT CUSHION COVER WITH PAD

    A01INQP

    1. Set the seat cushion cover with pad in place.

    2. Attach the hooks to install the seat cushion cover with pad.

    3. A01ITSBE02
      Text in Illustration
      *A w/ Seat Heater System
      *1 Wire Harness Clamp
      *2 Hook

      Attach the 3 hooks and wire harness clamp.

    4. w/ Seat Heater System:


      1. Connect the connector.

      2. A01IRLA

        Attach the 3 wire harness clamps.

    5. A01IOAP

      for Passenger Side:

      Attach the 2 hooks to connect the connector holder.

    6. A01IT5VE01
      Text in Illustration
      *1 Fastening Tape
      *2 Airbag Wire Harness

      Attach the piece of fastening tape to connect the airbag wire harness.

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. A01ISO3E01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

    4. A01IOL2

      Close the seatback cover and attach the 2 hooks as shown in the as illustration.

  5. INSTALL FRONT SEAT UNDER TRAY (w/ Under Tray)


    1. A01IOQH

      Attach the 2 hooks to install the front seat under tray.

  6. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A01IRB9E01
      Text in Illustration
      *1 Wire Harness Clamp
      *2 Hook

      Attach the wire harness clamp.

    2. Slide the front seat inner cushion shield LH to attach the hook.

    3. A01IT7C

      Push the front seat inner cushion shield LH to attach the hook and claw.

    4. Install the front seat inner cushion shield with the screw.

  7. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A01INSK

      Slide the front seat cushion shield LH to attach the 2 hooks.

      Text in Illustration
      A01ISER Slide
      A01ISM9 Push

    2. Push the front seat cushion shield LH to attach the claw.

    3. Install the front seat cushion shield LH with the 2 screws.

    4. A01IQQC

      Attach the 2 hooks to connect the 2 rubber bands.

  8. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A01ITUL

      Attach the claw to install the reclining adjuster release handle LH.

  9. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)

    A01IPV4

    1. Install the vertical adjusting handle LH with the 2 screws.

  10. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. A01IRXB

      Attach the 2 claws to install the vertical seat adjuster knob cap.

  11. INSTALL FRONT SEAT ASSEMBLY

    Click here

  12. CHECK SRS WARNING LIGHT

    Click here

  13. INSPECT FRONT SEAT ASSEMBLY


    1. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.