FRONT SEATBACK HEATER INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH


    1. A01IN2X

      Install the front seatback heater assembly LH to the front separate type front seatback cover with new tack pins.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A01ISKN

      Install the separate type front seatback pad.

    2. A01IR2IE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, connect the 2 straps to the separate type front seatback pad with new hog rings.

      Note

      Be careful not to damage the cover.

    3. A01IOZ4E01
      Text in Illustration
      *1 Seatback Wire
      *2 Hog Ring Pliers

      w/o Table:

      Using hog ring pliers, install the upper part of the separate type front seatback cover to the seatback wire with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    4. A01IOJJE01
      Text in Illustration
      *1 Seatback Wire
      *2 Hog Ring Pliers

      w/ Table:

      Using hog ring pliers, install the upper part of the separate type front seatback cover to the seatback wire with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    5. A01IQHC

      Attach the 2 hooks.

    6. A01IT8Q

      Attach the 2 hooks.

    7. A01ITUDE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket and install the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      After the separate type front seatback cover is installed, make sure the seatback cover bracket is not twisted.

    8. A01IMZIE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the center of the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    9. A01IRBBE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the 2 straps to the separate type front seatback pad with new hog rings.

    10. A01IP4B

      Attach the 2 hooks.

    11. A01IRRFE02
      Text in Illustration
      *1 Hog Ring
      *2 Hook
      *3 Lower Seatback Frame
      *4 Hog Ring Pliers

      Using hog ring pliers, attach the 2 straps to the lower seatback frame with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    12. Attach the 2 hooks.

    13. A01IRLYE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the 2 wires at the bottom of the separate type front seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  3. INSTALL FRONT SEATBACK TABLE ASSEMBLY LH (w/ Table)


    1. A01IMXC

      Install the front seatback table assembly LH with the 4 screws.

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. A01ISO3E01
      Text in Illustration
      *1 Protruding Part

      Install the front seat inner belt with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. for Driver Side:

      Connect the connector and attach the clamps.

    3. for Passenger Side:

      Connect the connectors and attach the clamps.

    4. A01IOL2

      Close the seatback cover and attach the 2 hooks as shown in the as illustration.

  5. INSTALL FRONT SEAT UNDER TRAY (w/ Under Tray)


    1. A01IOQH

      Attach the 2 hooks to install the front seat under tray.

  6. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. A01IRB9E01
      Text in Illustration
      *1 Wire Harness Clamp
      *2 Hook

      Attach the wire harness clamp.

    2. Slide the front seat inner cushion shield LH to attach the hook.

    3. A01IT7C

      Push the front seat inner cushion shield LH to attach the hook and claw.

    4. Install the front seat inner cushion shield with the screw.

  7. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. A01INSK

      Slide the front seat cushion shield LH to attach the 2 hooks.

      Text in Illustration
      A01ISER Slide
      A01ISM9 Push

    2. Push the front seat cushion shield LH to attach the claw.

    3. Install the front seat cushion shield LH with the 2 screws.

    4. A01IQQC

      Attach the 2 hooks to connect the 2 rubber bands.

  8. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. A01ITUL

      Attach the claw to install the reclining adjuster release handle LH.

  9. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)

    A01IPV4

    1. Install the vertical adjusting handle LH with the 2 screws.

  10. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. A01IRXB

      Attach the 2 claws to install the vertical seat adjuster knob cap.

  11. INSTALL FRONT SEAT ASSEMBLY

    Click here

  12. CHECK SRS WARNING LIGHT

    Click here

  13. INSPECT FRONT SEAT ASSEMBLY


    1. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.