REAR NO. 2 SEAT ASSEMBLY REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


  1. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Clean the rear No. 2 seat leg sub-assembly surface.

    2. A01ISQ4

      Attach a new rear No. 2 seat protector in the position shown in the illustration.

  2. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY

    A01IQA3E01
    Text in Illustration
    *1 Cable Tie

    1. Install the inner belt sub-assembly with the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Install a new cable tie.

    3. Attach the 3 clamps.

  3. INSTALL SEAT SPRING SILENCER LH


    1. Clean the No. 2 seatback frame sub-assembly LH surface.

    2. A01IQOH

      Attach a new seat spring silencer LH in the position shown in the illustration.

  4. INSTALL SEAT SPRING SILENCER RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL REAR SEAT RECLINING CONTROL CABLE LH


    1. A01IQRME01
      Text in Illustration
      *1 Cable Tie
      *2 Clamp

      Install the rear seat reclining control cable LH in the order shown in the illustration.

    2. Attach the 2 clamps of the cable ends.

    3. Install a new cable tie.

    4. A01IQZ8E02
      Text in Illustration
      *a Cut Here
      *b 5 mm (0.20 in.)
      *c Correct
      *d Incorrect

      Cut off the end of the cable tie as shown in the illustration.

      Tech Tips

      Make sure that the end of the cable tie faces the seatback board.

  6. INSTALL REAR SEAT RECLINING CONTROL CABLE RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL 3RD SEAT STRAP LH


    1. Install the 3rd seat strap LH with the screw.

      A01IUDJE01
      Text in Illustration
      *1 Seatback Frame Wire - -

  8. INSTALL 3RD SEAT STRAP RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    1. A01IO9FE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly LH to the rear No. 2 seat cushion pad LH with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  10. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH


    1. A01IQQNE01
      Text in Illustration
      *1 Slit

      Pass the No. 2 seat cushion frame sub-assembly LH through the slits in the rear seat cushion under cloth LH and install the rear seat cushion under cloth LH.

    2. A01IRTDE01
      Text in Illustration
      *1 Slit

      Pass the No. 2 seat cushion frame sub-assembly LH through the slits in the No. 2 seat cushion cover sub-assembly LH and install the No. 2 seat cushion frame sub-assembly LH.

    3. Attach the hooks.

    4. A01ISTGE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    5. A01IRU3E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    6. A01IPWUE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    7. A01IO05E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly LH to the No. 2 seat cushion frame sub-assembly LH with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  12. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL REAR SEAT LOWER CUSHION HINGE COVER RH


    1. A01ISJ7

      Attach the 2 claws to install the rear seat lower cushion hinge cover RH.

  14. INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH


    1. A01INUV

      Attach the 2 claws to install the rear seat lower cushion hinge cover LH.

  15. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH


    1. Using a T45 "TORX" socket wrench, install the rear No. 2 seat cushion assembly LH and 2 spacers with the 2 "TORX" bolts to the No. 2 seatback frame assembly LH.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }
    2. A01IQVL

      When reusing the nut:


      1. Clean the threads of the nut with non-residue solvent.

      2. Apply adhesive to the threads of the nut.

        Adhesive
        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      3. Temporarily install the nut and 2 bolts.

    3. When using a new nut:


      1. Temporarily install a new nut and the 2 bolts.

    4. Tighten the nut and 2 bolts.

      Torque:
      for Nut
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
      for Bolt
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    5. Install the No. 2 seat No. 2 suspension link and spacer.

    6. Install the spacer with the bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Install a new E-ring.

    8. Install the No. 2 seat No. 1 suspension link and spacer.

    9. Install the spacer with the bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    10. Install a new E-ring.

  16. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. INSTALL REAR SEAT CUSHION SPACER LH


    1. A01IUJ3

      Install the rear seat cushion spacer LH.

  18. INSTALL REAR SEAT CUSHION SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. INSTALL REAR NO. 2 SEAT CUSHION SPRING LH


    1. A01IN7M

      Attach the hook to install the rear No. 2 seat cushion spring LH.

  20. INSTALL REAR NO. 2 SEAT CUSHION SPRING RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. INSTALL REAR SEAT INNER RECLINING COVER LH


    1. A01IP9P

      Attach the hook to install the rear seat inner reclining cover LH.

  22. INSTALL REAR SEAT INNER RECLINING COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. INSTALL REAR SEAT SIDE HINGE MALE COVER LH


    1. A01ITQR

      Attach the hook to install the rear seat side hinge male cover LH.

    2. Install the screw.

  24. INSTALL REAR SEAT SIDE HINGE MALE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH


    1. A01INPPE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the center of the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad LH with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01IOLUE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the upper part of the No. 2 seatback cover sub-assembly LH to the No. 2 seatback pad LH with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  26. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD LH


    1. A01ITRY

      Install the rear No. 2 seatback cover with pad LH.

    2. Pass the 3rd seat strap through the hole of the rear No. 2 seatback cover with pad LH to the surface.

  28. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. INSTALL REAR SEATBACK LOCK HOOK LH


    1. A01IOHX

      Install the rear seatback lock hook LH.

  30. INSTALL REAR SEATBACK LOCK HOOK RH

    Tech Tips

    Use the same procedure described for the LH side.

  31. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY LH


    1. A01ISZT

      Attach the 4 claws to install the 2 rear No. 2 seat headrest supports assemblies.

  32. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  33. INSTALL SEATBACK FELT LH

    A01ISWLE01
    Text in Illustration
    *1 Seatback Felt

    1. Clean the rear seatback board sub-assembly LH surface.

    2. Attach a new seatback felt LH in the position shown in the illustration.

  34. INSTALL SEATBACK FELT RH

    Tech Tips

    Use the same procedure described for the LH side.

  35. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01IU29

      Attach the 6 hooks to install the rear seatback cloth LH to the rear seatback board sub-assembly LH.

    2. A01IU1ME01

      Attach the 2 hooks.

    3. Pass the 3rd seat strap through the hole of the rear seatback board sub-assembly LH to the surface.

      Text in Illustration
      *1 3rd Seat Strap
      *2 Seatback Felt

    4. Attach the 3 claws.

    5. Install the 2 screws.

    6. Remove the peeling paper from the seatback felt LH while being careful not to touch the exposed adhesive.

    7. Attach the hooks to install the rear seatback board sub-assembly LH.

  36. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. INSTALL REAR NO. 2 SEAT RECLINING COVER LH


    1. A01IQ4P

      Attach the 2 hooks to install the rear No. 2 seat reclining cover LH.

    2. Install the screw.

  38. INSTALL REAR NO. 2 SEAT RECLINING COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. INSTALL REAR SEAT CUSHION HINGE COVER


    1. A01ISOM

      Attach the 2 guides to install the rear seat cushion hinge cover.

    2. Install the screw.

    3. Install the screw.

  40. INSTALL NO. 2 SEAT HEADREST ASSEMBLY LH


    1. Install the No. 2 seat headrest assembly LH.

  41. INSTALL NO. 2 SEAT HEADREST ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.