REAR NO. 1 SEAT ASSEMBLY REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY LH


    1. Install the No. 1 seatback frame sub-assembly LH with the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY

    A01IQB7E01
    Text in Illustration
    *1 Cable Tie
    *2 Clamp

    1. Install the No. 2 seat adjuster control cable assembly in the order shown in the illustration.

    2. Attach the 2 clamps of the cable ends.

    3. Install 2 new cable ties.

    4. A01IQZ8E02
      Text in Illustration
      *a Cut Here
      *b 5 mm (0.20 in.)
      *c Correct
      *d Incorrect

      Cut off the end of the cable tie as shown in the illustration.

      Tech Tips

      Make sure that the end of the cable tie faces the seatback board.

  3. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

    A01IUEPE01
    Text in Illustration
    *1 Cable Tie
    *2 Clamp
    *a Blue Colored

    1. Install the rear No. 1 seat lock cable assembly in the order shown in the illustration.

    2. Attach the clamp of the cable end.

    3. Install a new cable tie.

    4. A01IQZ8E02
      Text in Illustration
      *a Cut Here
      *b 5 mm (0.20 in.)
      *c Correct
      *d Incorrect

      Cut off the end of the cable tie as shown in the illustration.

      Tech Tips

      Make sure that the end of the cable tie faces the seatback board.

  4. INSTALL RECLINING REMOTE CONTROL CABLE ASSEMBLY

    A01IS42E01
    Text in Illustration
    *a Green Colored

    1. Install the reclining remote control cable assembly in the order shown in the illustration.

    2. Attach the clamp of the cable end.

  5. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

    A01ISN3E01
    Text in Illustration
    *a Yellow Colored

    1. Install the rear No. 1 seat lock cable assembly in the order shown in the illustration.

    2. Attach the clamp of the cable end.

  6. INSTALL RECLINING REMOTE CONTROL CABLE ASSEMBLY

    A01IO60E01
    Text in Illustration
    *a Red Colored

    1. Install the reclining remote control cable assembly in the order shown in the illustration.

    2. Attach the clamp of the cable end.

  7. INSTALL NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY LH


    1. Temporarily install the rear No. 1 seat cushion frame sub-assembly LH with the 2 bolts.

    2. Using a T45 "TORX" socket wrench, temporarily install the 2 spacers with the 2 "TORX" bolts.

    3. Using a T45 "TORX" socket wrench, tighten the 2 "TORX" bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    4. Tighten the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  8. INSTALL REAR NO. 1 SEATBACK SPRING


    1. A01ISC9

      Temporarily install the rear back lock control lever RH.

    2. Operate the rear back lock control lever and fold down the seatback frame.

    3. A01ISDJ

      Attach the 4 hooks to install the 2 rear No. 1 seatback springs.

    4. A01IP58

      Operate the rear back lock control lever and raise the seatback frame.

    5. Remove the rear back lock control lever RH.

  9. INSTALL REAR SEATBACK COVER RH


    1. A01ISU8

      Attach the guide and 2 claws to install the rear seatback cover RH.

  10. INSTALL REAR SEATBACK COVER LH


    1. A01IT92

      Attach the guide and 2 claws to install the rear seatback cover LH.

  11. INSTALL REAR SEATBACK LOWER COVER SUB-ASSEMBLY LH


    1. Install the lower part of the rear seatback lower cover sub-assembly LH to the rear seatback lower pad.

    2. Using hog ring pliers, install the rear seatback lower cover sub-assembly LH to the rear seatback lower pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A01IQDEE01
      Text in Illustration
      *1 Hog Ring Pliers - -

    3. Using hog ring pliers, install the rear seatback lower cover sub-assembly LH with rear seatback lower pad to the seatback frame with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A01IOPZE01
      Text in Illustration
      *1 Hog Ring Pliers - -

    4. Using hog ring pliers, install new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A01ISCNE01
      Text in Illustration
      *1 Hog Ring Pliers - -

  12. INSTALL SEPARATE TYPE REAR SEATBACK COVER


    1. A01IT95E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01IU2HE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the lower part of the separate type rear seatback cover with a new hog ring.

      Note


      • Be careful not to damage the cover.

      • When installing the hog ring, avoid wrinkling the cover.

  13. INSTALL REAR NO. 1 SEATBACK COVER WITH PAD


    1. A01ITFR

      Temporary install the rear No. 1 seatback cover with pad.

    2. A01IR51

      Attach the 4 claws to install the 2 rear seat headrest supports.

    3. Using hog ring pliers, install the rear No. 1 seatback cover with pad to the seatback frame with new hog rings and attach the 2 hooks.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A01IQFCE01
      Text in Illustration
      *1 Hog Ring Pliers *2 Hog Ring
      *3 Hook - -
    4. A01IS14

      Attach the 2 hooks.

    5. A01IT7QE01
      Text in Illustration
      *1 Rubber Band

      Attach the 2 rubber bands and 3 hooks to install the rear No. 1 seatback cover with pad.

  14. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01ISES

      Attach the 2 hooks.

    2. Attach the 2 claws.

    3. Attach the 3 hooks to install the rear seatback board sub-assembly LH.

  15. INSTALL REAR NO. 1 SEATBACK BOARD

    A01IRWTE01
    Text in Illustration
    *1 Hook
    *2 Guide

    1. Attach the guide and 2 hooks.

    2. Attach the 4 claws to install the rear No. 1 seatback board.

  16. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    1. A01IRG5E03

      Connect the 2 cables in the order shown in the illustration.

    2. Attach the 2 clamps of the cable ends.

      Text in Illustration
      *a Blue Colored
      *b Yellow Colored
    3. A01INI1

      Attach the 2 claws to install the rear back lock control lever sub-assembly RH.

    4. Install the screw.

  17. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH


    1. A01IPY9E02

      Connect the 2 cables in the order shown in the illustration.

    2. Attach the 2 clamps of the cable ends.

      Text in Illustration
      *a Green Colored
      *b Red Colored
    3. A01INAW

      Attach the 2 claws to install the rear back lock control lever sub-assembly LH.

    4. Install the screw.

  18. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER


    1. A01IUR3E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01IOS3E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the separate type rear seat cushion cover to the separate type rear seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  19. INSTALL REAR NO. 1 SEAT CUSHION COVER WITH PAD


    1. Attach the 5 hooks to install the rear No. 1 seat cushion cover with pad.

    2. Using hog ring pliers, attach the separate type rear seat cushion cover to the separate type rear seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A01IU99E01
      Text in Illustration
      *1 Hog Ring Pliers - -

    3. Close the upper part of the separate type rear seat cushion cover.

    4. A01IQKX

      Attach the rubber band as shown in the illustration.

    5. Pass the 2 seatback cover rubber bands through the 2 seat cushion cover rubber bands.

    6. Attach the 2 seatback cover rubber bands.

      A01IRCOE01
      Text in Illustration
      *1 Seatback Cover Rubber Band *2 Seat Cushion Cover Rubber Band
    7. A01IN9Z

      Attach the 2 hooks to close the cover.

  20. INSTALL REAR SEAT LEG SIDE COVER LH

    A01ISA1E01
    Text in Illustration
    *1 Hook A
    *2 Hook B

    1. Attach the hook labeled A.

    2. Attach the 2 hooks labeled B to install the rear seat leg side cover LH.

    3. Install the 2 screws.

  21. INSTALL REAR SEAT 3 POINT TYPE INNER BELT ASSEMBLY LH

    A01IR3TE01

    1. Install the inner belt with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the seat inner belt to overlap the protruding parts of the seat frame.

      Text in Illustration
      *1 Protruding Part
      *2 Tape
      *3 Rubber Band

    2. Attach the clamps as shown in the illustration.

    3. Attach the rubber band.

    4. A01IO0C

      Attach the clamps.

  22. INSTALL REAR SEAT TRACK COVER LH


    1. A01IQTD

      Attach the guide and clip.

    2. Attach the 2 claws to install the rear seat track cover LH.

  23. INSTALL REAR SEAT NO. 2 LEG SIDE COVER

    A01IN3GE01
    Text in Illustration
    *1 Hook A
    *2 Hook B

    1. Attach the 3 hooks labeled A.

    2. Attach the 2 hooks labeled B to install the rear seat No. 2 leg side cover.

    3. Install the screw.

  24. INSTALL REAR SEAT HEADREST ASSEMBLY


    1. Install the rear seat headrest assembly.