REAR AIRBAG SENSOR (w/ Rear No. 2 Seat) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL REAR AIRBAG SENSOR LH


    1. A01IOYJ

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • w/ Navigation System (for HDD):

        After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    3. Install the rear airbag sensor with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

      • When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    4. Check that the rear airbag sensor is not loose.

    5. Connect the connector.

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Attach the 6 clips and 7 claws to install the deck trim side panel.

    3. Install the 2 bolts.

      A01ISVL
    4. A01IULD

      w/ Rear No. 1 Seat:

      Install the rear No. 1 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. A01IRRR

      w/ Rear No. 2 Seat:

      Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
  3. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

    A01IUD8

    Tech Tips

    Use the same procedure for all the luggage hold belt strikers.


    1. Install the luggage hold belt striker with the bolt.

  4. INSTALL DECK TRIM SIDE SERVICE HOLE COVER

    A01IQ10

    Tech Tips

    Use the same procedure to install the deck trim side service hole cover on the other side.


    1. Attach the 4 claws and 2 guides to install the deck trim side service hole cover.

  5. INSTALL FRONT DECK SIDE TRIM COVER LH

    A01IUCE

    1. Attach the 2 claws to install the front deck side trim cover.

  6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A01IP6WE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the weatherstrip as shown in the illustration.

  7. INSTALL REAR DOOR SCUFF PLATE LH

    A01IQ4G

    1. Attach the 9 claws and 2 clips to install the rear door scuff plate.

  8. INSTALL REAR DECK TRIM COVER

    A01ITUG

    1. Attach the 6 claws and 4 guides to install the rear deck trim cover.

  9. INSTALL REAR NO. 2 SEAT ASSEMBLY


    1. Place the rear No. 2 seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Temporarily install the 2 bolts.

      A01IUCV
    3. Pull the 2 straps and raise the 2 seatbacks.

    4. Temporarily install the 5 bolts.

      A01IRCI
    5. Tighten the bolts in the order shown in the illustration.

      A01IST0E01
      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
    6. Connect the connector under the seat.

  10. INSTALL REAR NO. 2 SEAT TRACK COVER


    1. A01IOQC

      Attach the 2 guides and claw.

    2. Attach the 2 claws to install the cover.

  11. INSTALL REAR NO. 2 SEAT TRACK BRACKET COVER

    Tech Tips

    Use the same procedure to install the cover on the other side.


    1. A01IQ45

      Attach the 2 claws to install the cover.

  12. INSTALL DECK TRIM SIDE BELT HOLE COVER LH

    A01IRMT

    1. Slide the deck trim side belt hole cover in the direction indicated by the arrow in the illustration and attach the 2 claws and 6 guides to install it.

  13. INSTALL DECK TRIM SIDE BELT HOLE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL DECK FLOOR BOX LH

    A01IU1X

    1. w/o Rear No. 2 Seat:


      1. Attach the 4 claws to install the deck floor box.

    2. A01IN2Q

      w/ Rear No. 2 Seat:


      1. Attach the 3 claws and guide to install the deck floor box.

      2. Install the bolt.

  15. INSTALL DECK FLOOR BOX RH

    A01ISZR

    1. w/o Rear No. 2 Seat:


      1. Attach the 2 claws and guide to install the deck floor box.

    2. A01IPFF

      w/ Rear No. 2 Seat:


      1. Attach the 2 claws and guide to install the deck floor box.

      2. Install the bolt.

  16. INSTALL LUGGAGE COMPARTMENT TRAY (w/ Spare Tire)

    A01ISB5

    1. Install the luggage compartment tray.

  17. INSTALL DECK RAIL COVER (w/o Spare Tire)

    A01IP10

    1. Attach the 2 claws and 2 guides to install the deck rail cover.

    2. Install the clip.

  18. INSTALL DECK BOARD ASSEMBLY

    A01IRW6

    1. Attach the 4 claws and 6 clips to install the deck board.

  19. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A01IUDC

    1. Install the tonneau cover.

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    CAUTION:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  21. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.