Click here

REAR AIRBAG SENSOR (w/ Rear No. 2 Seat) REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here
  1. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    • w/ Navigation System (for HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Click here

    REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  3. Click here

    REMOVE DECK BOARD ASSEMBLY


    1. Detach the 4 claws and 6 clips, and remove the deck board.

  4. Click here

    REMOVE DECK RAIL COVER (w/o Spare Tire)


    1. Remove the clip.

    2. Detach the 2 claws and 2 guides, and remove the deck rail cover.

  5. Click here

    REMOVE LUGGAGE COMPARTMENT TRAY (w/ Spare Tire)


    1. Remove the luggage compartment tray.

  6. Click here

    REMOVE DECK FLOOR BOX LH


    1. w/o Rear No. 2 Seat:


      1. Detach the 4 claws and remove the deck floor box.

    2. A01IN2Q

      w/ Rear No. 2 Seat:


      1. Remove the bolt.

      2. Detach the 3 claws and guide, and remove the deck floor box.

  7. Click here

    REMOVE DECK FLOOR BOX RH


    1. w/o Rear No. 2 Seat:


      1. Detach the 2 claws and guide, and remove the deck floor box.

    2. A01IPFF

      w/ Rear No. 2 Seat:


      1. Remove the bolt.

      2. Detach the 2 claws and guide, and remove the deck floor box.

  8. Click here

    REMOVE DECK TRIM SIDE BELT HOLE COVER LH


    1. Detach the 2 claws and 6 guides, and remove the deck trim side belt hole cover in the direction indicated by the arrow in the illustration.

  9. Click here

    REMOVE DECK TRIM SIDE BELT HOLE COVER RH

    Tip:

    Use the same procedure described for the LH side.

  10. Click here

    REMOVE REAR NO. 2 SEAT TRACK BRACKET COVER

    Tip:

    Use the same procedure to remove the cover on the other side.


    1. A01IS71

      Detach the 2 claws and remove the cover.

  11. Click here

    REMOVE REAR NO. 2 SEAT TRACK COVER


    1. A01IPIR

      Detach the 3 claws and 2 guides, and then remove the cover.

  12. Click here

    REMOVE REAR NO. 2 SEAT ASSEMBLY


    1. Disconnect the connector under the seat.

    2. A01IRCI

      Remove the 5 bolts.

    3. A01ITYW

      Pull the 2 straps and fold down the 2 seatbacks.

    4. Remove the 2 bolts.

    5. Remove the rear No. 2 seat assembly from the vehicle.

      Note:

      Be careful not to damage the vehicle body.

  13. Click here

    REMOVE REAR DECK TRIM COVER


    1. Detach the 6 claws and 4 guides, and remove the rear deck trim cover.

  14. Click here

    REMOVE REAR DOOR SCUFF PLATE LH


    1. Detach the 9 claws and 2 clips, and remove the rear door scuff plate.

  15. Click here

    REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip.

  16. Click here

    REMOVE FRONT DECK SIDE TRIM COVER LH


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tip:

      Tape the screwdriver tip before use.

      Table 1. Text in Illustration
      *1 Protective Tape
  17. Click here

    REMOVE DECK TRIM SIDE SERVICE HOLE COVER

    Tip:

    Use the same procedure to remove the deck trim side service hole cover on the other side.


    1. Using a screwdriver, detach the 4 claws and 2 guides, and remove the deck trim side service hole cover.

      Tip:

      Tape the screwdriver tip before use.

      Table 2. Text in Illustration
      *1 Protective Tape
  18. Click here

    REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

    Tip:

    Use the same procedure for all the luggage hold belt strikers.


    1. Remove the bolt and luggage hold belt striker.

  19. Click here

    REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. w/ Rear No. 1 Seat:

      Remove the bolt and rear No. 1 seat belt anchor.

    2. A01IRRR

      w/ Rear No. 2 Seat:

      Remove the bolt and rear No. 2 seat belt anchor

    3. Remove the 2 bolts.

    4. Detach the 6 clips and 7 claws.

    5. A01ISVL

      Disconnect the connector and remove the deck trim side panel.

  20. Click here

    REMOVE REAR AIRBAG SENSOR LH


    1. A01IOYJ

      Remove the bolt and rear airbag sensor.

    2. Disconnect the connector.