REAR AIRBAG SENSOR (w/ Rear No. 2 Seat) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE BATTERY SERVICE HOLE COVER


    1. A01ITOM

      Remove the clip and battery service hole cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • w/ Navigation System (for HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    A01IUDC

    1. Remove the tonneau cover.

  4. REMOVE DECK BOARD ASSEMBLY

    A01IRW6

    1. Detach the 4 claws and 6 clips, and remove the deck board.

  5. REMOVE DECK RAIL COVER (w/o Spare Tire)

    A01IP10

    1. Remove the clip.

    2. Detach the 2 claws and 2 guides, and remove the deck rail cover.

  6. REMOVE LUGGAGE COMPARTMENT TRAY (w/ Spare Tire)

    A01ISB5

    1. Remove the luggage compartment tray.

  7. REMOVE DECK FLOOR BOX LH

    A01IU1X

    1. w/o Rear No. 2 Seat:


      1. Detach the 4 claws and remove the deck floor box.

    2. A01IN2Q

      w/ Rear No. 2 Seat:


      1. Remove the bolt.

      2. Detach the 3 claws and guide, and remove the deck floor box.

  8. REMOVE DECK FLOOR BOX RH

    A01ISZR

    1. w/o Rear No. 2 Seat:


      1. Detach the 2 claws and guide, and remove the deck floor box.

    2. A01IPFF

      w/ Rear No. 2 Seat:


      1. Remove the bolt.

      2. Detach the 2 claws and guide, and remove the deck floor box.

  9. REMOVE DECK TRIM SIDE BELT HOLE COVER LH

    A01IUQX

    1. Detach the 2 claws and 6 guides, and remove the deck trim side belt hole cover in the direction indicated by the arrow in the illustration.

  10. REMOVE DECK TRIM SIDE BELT HOLE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. REMOVE REAR NO. 2 SEAT TRACK BRACKET COVER

    Tech Tips

    Use the same procedure to remove the cover on the other side.


    1. A01IS71

      Detach the 2 claws and remove the cover.

  12. REMOVE REAR NO. 2 SEAT TRACK COVER


    1. A01IPIR

      Detach the 3 claws and 2 guides, and then remove the cover.

  13. REMOVE REAR NO. 2 SEAT ASSEMBLY


    1. Disconnect the connector under the seat.

    2. Remove the 5 bolts.

      A01IRCI

    3. Pull the 2 straps and fold down the 2 seatbacks.

      A01ITYW

    4. Remove the 2 bolts.

    5. Remove the rear No. 2 seat assembly from the vehicle.

      Note

      Be careful not to damage the vehicle body.

  14. REMOVE REAR DECK TRIM COVER

    A01ITUG

    1. Detach the 6 claws and 4 guides, and remove the rear deck trim cover.

  15. REMOVE REAR DOOR SCUFF PLATE LH

    A01IQ4G

    1. Detach the 9 claws and 2 clips, and remove the rear door scuff plate.

  16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A01ISHX

    1. Remove the rear door opening trim weatherstrip.

  17. REMOVE FRONT DECK SIDE TRIM COVER LH

    A01ING9E01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  18. REMOVE DECK TRIM SIDE SERVICE HOLE COVER

    A01IUGKE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure to remove the deck trim side service hole cover on the other side.


    1. Using a screwdriver, detach the 4 claws and 2 guides, and remove the deck trim side service hole cover.

      Tech Tips

      Tape the screwdriver tip before use.

  19. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

    A01IUD8

    Tech Tips

    Use the same procedure for all the luggage hold belt strikers.


    1. Remove the bolt and luggage hold belt striker.

  20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    A01IULD

    1. w/ Rear No. 1 Seat:

      Remove the bolt and rear No. 1 seat belt anchor.

    2. A01IRRR

      w/ Rear No. 2 Seat:

      Remove the bolt and rear No. 2 seat belt anchor

    3. Remove the 2 bolts.

    4. Detach the 6 clips and 7 claws.

    5. Disconnect the connector and remove the deck trim side panel.

      A01ISVL

  21. REMOVE REAR AIRBAG SENSOR LH


    1. A01IOYJ

      Remove the bolt and rear airbag sensor.

    2. Disconnect the connector.