Click here

AIRBAG SYSTEM Diagnosis Circuit

Click here
Click here Click here
DTC Code DTC Name
  Diagnosis Circuit
Click here

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

Tip:

  • When each warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

  • A DTC output mode signal is transmitted through the CAN communication system to each ECU including the center airbag sensor. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK CAN COMMUNICATION SYSTEM


    1. Check if a CAN communication system DTC is output.

      Table 1. Result
      Result Proceed to
      DTC is not output A
      DTC is output B

  2. Click here

    CHECK HARNESS AND CONNECTOR (DLC3 - ECM)


    1. A01IQDNE01

      Turn the ignition switch off.

    2. for ZR or AD Series Engine


      1. Disconnect the A51 connector from the ECM.

    3. for 1WW Engine


      1. Disconnect the A76 connector from the ECM.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for ZR Series Engine
      Tester Connection Condition Specified Condition
      H16-13 (TC) - A51-41 (TC) Always Below 1 Ω
      for AD Series Engine
      Tester Connection Condition Specified Condition
      H16-13 (TC) - A51-26 (TC) Always Below 1 Ω
      for 1WW Engine
      Tester Connection Condition Specified Condition
      H16-13 (TC) - A76-50 (TC) Always Below 1 Ω
      Table 2. Text in Illustration
      *1 Front view of DLC3
      *2

      Front view of wire harness connector

      (to ECM)
      *3 for ZR Series Engine
      *4 for AD Series Engine
      *5 for 1WW Engine

  3. Click here

    CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)


    1. A01IQPSE04

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H16-4 (CG) - Body ground Always Below 1 Ω
      Table 3. Text in Illustration
      *1 Front view of DLC3

  4. Click here

    CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)


    1. A01INKYE03

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for ZR Series Engine
      Tester Connection Condition Specified Condition
      A51-41 (TC) - Body ground Always 1 MΩ or higher
      for AD Series Engine
      Tester Connection Condition Specified Condition
      A51-26 (TC) - Body ground Always 1 MΩ or higher
      for 1WW Engine
      Tester Connection Condition Specified Condition
      A76-50 (TC) - Body ground Always 1 MΩ or higher
      Table 4. Text in Illustration
      *1

      Front view of wire harness connector

      (to ECM)
      *2 for ZR Series Engine
      *3 for AD Series Engine
      *4 for 1WW Engine

  5. Click here

    REPAIR TROUBLE AREAS INDICATED BY OUTPUT DTCSClick here

  6. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    REPLACE CENTER AIRBAG SENSOR ASSEMBLYClick here