AIRBAG SYSTEM, Diagnostic DTC:B1630/23

DTC Code DTC Name
B1630/23 Rear Airbag Sensor RH Circuit Malfunction

DESCRIPTION

The rear airbag sensor RH consists of a safing sensor, diagnostic circuit, lateral deceleration sensor, etc.

If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.

DTC B1630/23 is stored when a malfunction is detected in the rear airbag sensor RH circuit.

DTC Code Detection Condition Trouble Area
B1630/23

One of the following conditions is met:


  • A rear airbag sensor RH malfunction.

  • A center airbag sensor malfunction.

  • Rear airbag sensor RH

  • No. 2 floor wire

  • Center airbag sensor assembly

WIRING DIAGRAM

A01IS1NE05

INSPECTION PROCEDURE

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

PROCEDURE


  1. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connector is properly connected to the rear airbag sensor RH.

      OK
      The connector is properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  2. CHECK CONNECTORS


    1. A01IUFPE01
      Text in Illustration
      *1 Rear Airbag Sensor RH
      *2 No. 2 Floor Wire
      *3 Side Airbag Sensor RH

      Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

    2. Check that the connector (on the rear airbag sensor RH side) is not damaged.

      OK
      The connector is not deformed or damaged.

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  3. CHECK NO. 2 FLOOR WIRE (REAR AIRBAG SENSOR RH CIRCUIT)


    1. A01IP1JE09
      Text in Illustration
      *1 Rear Airbag Sensor RH
      *2 No. 2 Floor Wire
      *3 Side Airbag Sensor RH
      *4

      Rear view of wire harness connector

      (to Rear Airbag Sensor RH)
      *5 Connector C
      *6

      Rear view of wire harness connector

      (to Side Airbag Sensor RH)
      *7 Connector B
      *8 Service Wire

      Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      O19-2 (BCR+) - Body ground Ignition switch ON Below 1 V
      O19-1 (BCR-) - Body ground

    3. Turn the ignition switch off.

    4. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    5. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O19-2 (BCR+) - O19-1 (BCR-) Always Below 1 Ω

    7. Disconnect the service wire from connector B.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O19-2 (BCR+) - O19-1 (BCR-) Always 1 MΩ or higher
      O19-2 (BCR+) - Body ground
      O19-1 (BCR-) - Body ground

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  4. CHECK REAR AIRBAG SENSOR RH


    1. A01IO5HE01
      Text in Illustration
      *1 Rear Airbag Sensor LH
      *2 Side Airbag Sensor RH

      Interchange the rear airbag sensor LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1630 and B1635 are not output A
      DTC B1635 is output (w/ Rear No. 2 Seat) B
      DTC B1635 is output (w/o Rear No. 2 Seat) C
      DTC B1630 is output D

      Tech Tips

      Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    10. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.


    B

    REPLACE REAR AIRBAG SENSOR RH Click here

    C

    REPLACE REAR AIRBAG SENSOR RH Click here

    D

    CHECK SIDE AIRBAG SENSOR RH Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  5. CHECK SIDE AIRBAG SENSOR RH


    1. A01IP5VE26
      Text in Illustration
      *1 Side Airbag Sensor LH
      *2 Center Airbag Sensor

      Interchange the side airbag sensor LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1630 and B1635 are not output A
      DTC B1635 is output B
      DTC B1630 is output C

      Tech Tips

      Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    10. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    A

    USE SIMULATION METHOD TO CHECK Click here