Click here

AIRBAG SYSTEM, Diagnostic DTC:B1610/13

Click here
Click here Click here
DTC Code DTC Name
B1610/13 Front Airbag Sensor RH Circuit Malfunction
Click here

SYSTEM DESCRIPTION

The front airbag sensor RH consists of a diagnostic circuit and frontal deceleration sensor, etc. If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether the SRS should be activated.

DTC B1610/13 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1610/13

One of the following conditions is met:


  • A front airbag sensor RH malfunction.

  • A center airbag sensor malfunction.


  • Front airbag sensor RH

  • Engine room main wire

  • Instrument panel wire

  • Center airbag sensor assembly

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor and front airbag sensor RH.

      OK
      The connectors are properly connected.

  2. Click here

    CHECK CONNECTORS


    1. A01IUPTE01

      Disconnect the connectors from the center airbag sensor and front airbag sensor RH.

    2. Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

      OK
      The connectors are not deformed or damaged.
      Table 1. Text in Illustration
      *1 Front Airbag Sensor RH
      *2 Center Airbag Sensor

  3. Click here

    CHECK FRONT AIRBAG SENSOR RH CIRCUIT


    1. A01INX1E02

      Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A23-2 (+SR) - Body ground Ignition switch ON Below 1 V
      A23-1 (-SR) - Body ground Ignition switch ON Below 1 V
    3. Turn the ignition switch off.

    4. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    5. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A23-2 (+SR) - A23-1 (-SR) Always Below 1 Ω
    7. Disconnect the service wire from connector B.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A23-2 (+SR) - A23-1 (-SR) Always 1 MΩ or higher
      A23-2 (+SR) - Body ground Always 1 MΩ or higher
      A23-1 (-SR) - Body ground Always 1 MΩ or higher
      Table 2. Text in Illustration
      *1 Front Airbag Sensor RH
      *2 Center Airbag Sensor
      *3

      Front view of wire harness connector

      (to Front Airbag Sensor RH)

      *4 Connector E
      *5

      Rear view of wire harness connector

      (to Center Airbag Sensor)

      *6 Connector B
      *7 Service Wire

  4. Click here

    CHECK FRONT AIRBAG SENSOR RH


    1. A01IR36E01

      Connect the connectors to the center airbag sensor.

    2. Interchange the front airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory (Click here).

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs (Click here).

      Table 3. Result
      Result Proceed to
      DTC B1610 and B1615 are not output A
      DTC B1615 is output B
      DTC B1610 is output C
      Tip:

      Codes other than DTC B1610 and B1615 may be output at this time, but they are not related to this check.

      Table 4. Text in Illustration
      *1 Front Airbag Sensor LH
      *2 Center Airbag Sensor

  5. Click here

    CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)


    1. A01IU7SE02

      Disconnect the instrument panel wire connector from the engine room main wire.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      AH9-2 (+SR) - Body ground Ignition switch ON Below 1 V
      AH9-1 (-SR) - Body ground Ignition switch ON Below 1 V
    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      AH9-2 (+SR) - AH9-1 (-SR) Always Below 1 Ω
    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      AH9-2 (+SR) - AH9-1 (-SR) Always 1 MΩ or higher
      AH9-2 (+SR) - Body ground Always 1 MΩ or higher
      AH9-1 (-SR) - Body ground Always 1 MΩ or higher
      Table 5. Text in Illustration
      *1 Front Airbag Sensor RH
      *2 Engine Room Main Wire
      *3 Instrument Panel Wire
      *4 Center Airbag Sensor
      *5

      Front view of wire harness connector

      (to Engine Room Main Wire)

      *6 Connector C
      *7

      Rear view of wire harness connector

      (to Center Airbag Sensor)

      *8 Connector B
      *9 Service Wire

  6. Click here

    CONNECT CONNECTORS PROPERLY

  7. Click here

    REPLACE HARNESS AND CONNECTOR

  8. Click here

    USE SIMULATION METHOD TO CHECKClick here

  9. Click here

    REPLACE FRONT AIRBAG SENSOR RHClick here

  10. Click here

    REPLACE CENTER AIRBAG SENSOR ASSEMBLYClick here

  11. Click here

    REPLACE INSTRUMENT PANEL WIRE

  12. Click here

    REPLACE ENGINE ROOM MAIN WIRE