Click here

ENTRY AND START SYSTEM (for Start Function) Power Source Mode does not Change to ON (ACC)

Click here
Click here Click here
DTC Code DTC Name
  Power Source Mode does not Change to ON (ACC)
Click here

DESCRIPTION

When the engine switch is pushed with the key in the cabin, the power management control ECU receives signals to switch the power source mode.

Tip:

To allow use of the intelligent tester to inspect the push-button start function when the engine switch is off, repeatedly open and close any of the doors. Repeatedly opening and closing a door establishes communication between the intelligent tester and power management control ECU (opening and closing a door can also be simulated by operating a door courtesy light switch).

Click here

WIRING DIAGRAM

Refer to "Power Source Mode does not Change to on (IG and ACC)" (Click here).

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    1. A01IUFQE04

      Disconnect the H71 power management control ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H71-2 (AM21) - Body ground Always 9.5 to 16 V
      H71-1 (AM22) - Body ground
      Table 1. Text in Illustration
      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

  2. Click here

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)


    1. Disconnect the H71 power management control ECU connector.

    2. A01IUFQE05

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H71-6 (GND) - Body ground Always Below 1 Ω
      H71-5 (GND2) - Body ground
      Table 2. Text in Illustration
      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

  3. Click here

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. A01IUHVE02

      Disconnect the H71 power management control ECU and DM instrument panel junction block assembly connectors.

      Table 3. Text in Illustration
      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

      		 *2

      Front view of wire harness connector

      (to Instrument Panel Junction Block Assembly)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H71-19 (ACCD) - DM-7 20°C (68°F) 75 to 117 Ω
      H71-19 (ACCD) - Body ground Always 10 kΩ or higher

  4. Click here

    INSPECT ACC RELAY


    1. A01IN8WE02

      Remove the ACC relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      3 - 5 When battery voltage is applied to terminals 1 and 2 Below 1 Ω

  5. Click here

    CHECK POWER MANAGEMENT CONTROL ECU


    1. A01IUO1E11

      Connect the power management control ECU connector.

      Table 4. Text in Illustration
      *1

      Component with harness connected

      (Power Management Control ECU)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H71-19 (ACCD) - Body ground Engine switch off Below 1.0 V
      Engine switch on (ACC) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
      Table 5. Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

  6. Click here

    CHECK ENGINE SWITCH


    1. Check that the power source mode changes to on (ACC) and on (IG) when operating the engine switch.

      OK
      The power source mode changes to on (ACC) and on (IG) in response to the operation of the engine switch.

  7. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE ACC RELAY


    1. Replace the ACC relay with a new or normally functioning part, or repair or replace any damaged wire harness or connector.


  8. Click here

    CHECK POWER MANAGEMENT CONTROL ECU


    1. A01IUO1E11

      Connect the power management control ECU connector.

      Table 6. Text in Illustration
      *1

      Component with harness connected

      (Power Management Control ECU)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H71-19 (ACCD) - Body ground Engine switch off Below 1.0 V
      Engine switch on (ACC) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
      Table 7. Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

  9. Click here

    CHECK ENGINE SWITCH


    1. Check that the power source mode changes to on (ACC) and on (IG) when operating the engine switch.

      OK
      The power source mode changes to on (ACC) and on (IG) in response to the operation of the engine switch.

  10. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  11. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. Click here

    REPLACE POWER MANAGEMENT CONTROL ECUClick here

  13. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ACC RELAY)

  14. Click here

    END

  15. Click here

    REPLACE POWER MANAGEMENT CONTROL ECUClick here