Click here

ENTRY AND START SYSTEM (for Start Function), Diagnostic DTC:B2281

Click here
Click here Click here
DTC Code DTC Name
B2281 "P" Signal Malfunction
Click here

DESCRIPTION

This DTC is stored when there is an abnormal circuit between the power management control ECU and the shift lock control ECU.

Tip:

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

DTC No. DTC Detection Condition Trouble Area
B2281 Communication or the communication line between the power management control ECU and shift lock control ECU is abnormal.

  • Power management control ECU

  • Shift lock control ECU

  • Harness or connector
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    READ VALUE USING INTELLIGENT TESTER (SHIFT P SIGNAL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. According to the display on the intelligent tester, read the Data List.

      Table 1. Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Shift P Signal Shift P position signal/ON or OFF

      ON: Shift lever in P

      OFF: Shift lever not in P

      		 -
      OK
      ON (shift lever in P) or OFF (shift lever not in P) appears on the screen according to the shift lever position.
      Table 2. Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

  2. Click here

    INSPECT SHIFT LOCK CONTROL ECU


    1. A01IUAGE02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      11 (P2) - 3 (E) Shift lever in P Below 1 Ω
      11 (P2) - 3 (E) Shift lever not in P 10 kΩ or higher
      Table 3. Text in Illustration
      *1

      Component without harness connected

      (Shift Lock Control ECU)

  3. Click here

    CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU AND BODY GROUND - SHIFT LOCK CONTROL ECU)


    1. A01ISI8E01

      Disconnect the H71 connector from the power management control ECU.

    2. Disconnect the H5 connector from the shift lock control ECU.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H71-16 (P) - H5-11 (P2) Always Below 1 Ω
      H71-16 (P) or H5-11 (P2) - Body ground Always 10 kΩ or higher
      H71-6 (GND) or H5-3 (E) - Body ground Always Below 1 Ω
      Table 4. Text in Illustration
      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

      		 *2

      Front view of wire harness connector

      (to Shift Lock Control ECU)
      Table 5. Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

  4. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. Click here

    REPLACE SHIFT LOCK CONTROL ECUClick here

  6. Click here

    REPLACE POWER MANAGEMENT CONTROL ECUClick here

  7. Click here

    REPLACE POWER MANAGEMENT CONTROL ECUClick here