ENTRY AND START SYSTEM (for Entry Function), Diagnostic DTC:B27A2

DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the front door outside handle assembly (for passenger side) at an interval of 250 ms. The front door outside handle assembly (for passenger side) detects when the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the passenger door, the signal is transmitted at the frequency stated above. DTC B27A2 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and the front door outside handle assembly (for passenger side) (CLG2 - ANT1, CG2B - ANT2).

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK CONNECTOR CONNECTION CONDITION

   
   

   1. Turn the engine switch off.

   2. Check that the connectors are properly connected to the certification ECU and front door outside handle assembly (for passenger side).

      OK
      Connectors are properly connected.

   
   

   NG

   CONNECT CONNECTORS PROPERLY

   OK

2. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU)

   
   
   1. 

      Text in Illustration

      *1	for LHD
      *2	for RHD
      *3	Front view of wire harness connector (to Front Door Outside Handle Assembly [for Passenger Side])
      *4	Front view of wire harness connector (to Certification ECU)

      Disconnect the H51 ECU connector.

   2. Disconnect the J10*1 or K6*2 handle connector.

      
      

      • *1: for LHD

      • *2: for RHD

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition J10-3 (ANT2) - H51-6 (CG2B) Always Below 1 Ω J10-6 (ANT1) - H51-5 (CLG2) Always Below 1 Ω J10-2 (GND) - Body ground Always Below 1 Ω H51-6 (CG2B) - Body ground Always 10 kΩ or higher H51-5 (CLG2) - Body ground Always 10 kΩ or higher H51-15 (E) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition K6-3 (ANT2) - H51-6 (CG2B) Always Below 1 Ω K6-6 (ANT1) - H51-5 (CLG2) Always Below 1 Ω K6-2 (GND) - Body ground Always Below 1 Ω H51-6 (CG2B) - Body ground Always 10 kΩ or higher H51-5 (CLG2) - Body ground Always 10 kΩ or higher H51-15 (E) - Body ground Always Below 1 Ω

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

3. CHECK CERTIFICATION ECU

   
   

   1. Measure the voltage according to the value(s) in the table below.

      

      Standard Voltage

      Tester Connection Switch Condition Specified Condition H51-5 (CLG2) - H51-15 (E) Engine switch off, all doors closed, and key not in cabin No pulse generation H51-5 (CLG2) - H51-15 (E) Engine switch off, all doors closed, all doors locked with wireless door lock control and key not in cabin Pulse generation H51-6 (CG2B) - H51-15 (E) Engine switch off, all doors closed, and key not in cabin No pulse generation H51-6 (CG2B) - H51-15 (E) Engine switch off, all doors closed, all doors locked with wireless door lock control and key not in cabin Pulse generation

      Text in Illustration

      *1

      Component with harness connected (Certification ECU)

      -

      -

   
   

   NG

   REPLACE CERTIFICATION ECU

   OK

4. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE)

   
   

   1. Temporarily replace the front door outside handle assembly (for passenger side) with a new or normally functioning one Click here.

   
   

   NEXT

5. CHECK FOR DTC

   
   

   1. Clear the DTCs Click here.

   2. Check for DTCs Click here.

      OK
      DTC B27A2 is not output.

   
   

   NG

   REPLACE CERTIFICATION ECU

   OK

   END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY IS DEFECTIVE)