FRONT DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    1. A01IQLV

      Using moulding remover A, detach the 3 claws and remove the inside handle bezel.

  4. REMOVE FRONT DOOR TRIM MOULDING LH


    1. A01IS9F

      Using moulding remover A, detach the 8 claws and remove the front door trim moulding.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. A01IN0RE01

      Using moulding remover A, detach the clip and 7 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector.

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01IR1B

      Remove the 3 screws.

    2. Remove the 9 clips.

    3. w/ Courtesy Light:


      1. Disconnect the courtesy light connector.

    4. A01IP9CE01
      Text in Illustration
      *1 Reference Boss

      Pull out the front door trim board in the direction indicated by the arrow.

    5. A01IUDS

      Disconnect the 2 cables from the inside handle.

  7. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A01IUHM

      Detach the 2 claws and remove the inside handle sub-assembly from the door trim board.

  8. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A01IUMH

      Detach the 5 claws and remove the weatherstrip.

  9. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01IOWT

      Disconnect the 2 connectors and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. for Driver Side:

      Temporarily install the master switch assembly.

    2. for Front Passenger Side:

      Temporarily install the regulator switch assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Move the door glass until the bolts appear in the service holes.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

    6. A01ITCI

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    7. A01IRRQ

      Remove the door glass in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

    8. for Driver Side:

      Remove the master switch assembly.

    9. for Front Passenger Side:

      Remove the regulator switch assembly.

  11. REMOVE FRONT DOOR GLASS RUN LH


    1. A01IQYV

      Remove the front door glass run.

  12. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    1. A01IR7H

      Remove the bolt and rear lower frame.

  13. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)


    1. A01IOHI

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the cover with the door lock key cylinder installed.

    3. A01INZV

      Using a screwdriver, disengage the 3 claws and remove the front door outside handle cover from the cylinder.

  14. REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)


    1. A01IN0O

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover.

  15. REMOVE FRONT DOOR LOCK ASSEMBLY LH


    1. A01IPV7E01

      Using a T30 "TORX" wrench, remove the 3 screws.

    2. Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.

    3. Remove the front door lock open rod from the front door lock assembly.

    4. Remove the door lock wiring harness seal from the front door lock assembly.

  16. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A01IOB1

      Remove the front door lock remote control cable assembly.

  17. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A01ISCC

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01IN6F

      Remove the front door inside locking cable assembly.