REAR DOOR LOCK INSTALLATION

INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

1. 

   Install the rear door inside locking cable.

2. 

   Attach the 3 claws.

INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

1. 

   Install the rear door lock remote control cable.

2. 

   Attach the claw.

INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

1. w/ Power Window:

   
   

   1. Temporarily install the regulator switch assembly.

   2. Connect the cable to the negative (-) battery terminal.

   3. Operate the regulator switch until the regulator reaches its bottom dead center.

   4. Disconnect the cable from the negative (-) battery terminal.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

   5. Remove the regulator switch assembly.

2. w/o Power Window:

   
   

   1. Temporarily install the rear door window regulator handle assembly.

   2. Turn the handle until the regulator reaches its bottom dead center.

   3. Remove the rear door window regulator handle assembly.

3. 

   Install the front side of the glass run.

4. 

   Apply MP grease to the sliding areas of the glass channel as shown in the illustration.

   Standard
   Area Specified Condition A 130 mm (5.12 in.) B 29 mm (1.14 in.)

5. 

   Slide the rear door glass sub-assembly as shown in the illustration to install it.

INSTALL REAR DOOR QUARTER WINDOW GLASS LH

1. 

   Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

1. 

   Insert the rear door window division bar sub-assembly from above.

2. Install the rear door window division bar sub-assembly to the glass run.

3. 

   Install the rear door window division bar sub-assembly with the 2 bolts and screw.

   6.2 N*m

   63 kgf*cm

   55 in.*lbf

   for bolt and screw

INSTALL REAR DOOR GLASS RUN LH

1. 

   Completely install the glass run.

INSTALL REAR DOOR SERVICE HOLE COVER LH

1. Apply butyl tape to the door.

2. 

   Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

   Table 1. Text in Illustration

   *1	Reference Point

3. Install the rear door service hole cover by using the reference points on the rear door panel.

   Note:
   

   • There should be no wrinkles or folds after attaching the service hole cover.

   • After attaching the service hole cover, check the seal quality.

4. Connect the connector.

INSTALL REAR DOOR INSIDE PANEL REINFORCE SUB-ASSEMBLY LH

1. 

   Install the rear door inside panel reinforce sub-assembly to the door panel with the 2 bolts and 2 screws.

INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

1. 

   Install the rear door inner glass weatherstrip to the door panel.

INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

1. 

   Connect the 2 cables to the inside handle to install the inside handle.

INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

1. 

   Install the clamp to the door panel.

2. 

   Attach the 2 claws to install the inside handle to the rear door trim board.

3. 

   Attach the rear door trim board with the 4 claws on the rear door inner glass weatherstrip.

   Table 2. Text in Illustration

   *1	w/ Rear Door Sunshade
   *2	w/o Rear Door Sunshade

4. 

   Install the rear door trim board with the 10 clips.

5. Install the 3 screws.

INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

1. Connect the connector.

2. 

   Attach the 4 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

INSTALL REAR DOOR TRIM MOULDING LH

1. 

   Attach the 8 claws to install the door trim moulding.

INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

1. 

   Attach the 3 claws to install the rear door inside handle bezel.

INSTALL REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)

1. Install the rear door regulator inside handle plate.

INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

1. Temporarily install the rear door window regulator handle assembly, fully close the window, and then remove the rear door window regulator handle assembly.

2. Install the snap ring to the rear door window regulator handle assembly.

3. 

   Install the rear door window regulator handle assembly as shown in the illustration.

   Table 3. Text in Illustration

   *1	Front Side

   Standard
   Area Specified Condition A 50° to 60°

INSTALL BATTERY SERVICE HOLE COVER

1. 

   Install the battery service hole cover with the clip.