Click here

POWER DOOR LOCK CONTROL SYSTEM All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder

Click here
Click here Click here
DTC Code DTC Name
  All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder
Click here

DESCRIPTION

The main body ECU (instrument panel junction block assembly) receives switch signals from the master switch, and front door lock key cylinder switch signals from the front door lock. The main body ECU (instrument panel junction block assembly) activates the door lock motor on each door according to these signals.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

Click here

PROCEDURE


  1. Click here

    CHECK DOOR LOCK OPERATION


    1. Check the door lock operation.

      Table 1. Result
      Result Proceed to
      No doors can be locked with master switch or front door lock key cylinder A
      No doors can be locked with master switch B
      No doors can be locked with front door lock key cylinder C

  2. Click here

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)


    1. A01IRVNE02

      Disconnect the DE, DG, H79 and H80 ECU connectors.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      DG-1 (ALTB) - Body ground Always 11 to 14 V
      H79-4 (BATB) - Body ground Always 11 to 14 V
      Standard Resistance
      Tester Connection Condition Specified Condition
      DE-28 (GND1) - Body ground Always Below 1 Ω
      H80-4 (GND2) - Body ground Always Below 1 Ω
      Table 2. Text in Illustration
      *1

      Front view of wire harness connector

      (to Main Body ECU)

      		 - -

  3. Click here

    CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (OPERATION)


    1. Replace the master switch with a normally functioning one (Click here).

    2. Check that all doors can be locked and unlocked by using the master switch.

      OK
      All doors can be locked and unlocked with master switch.

  4. Click here

    READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)


    1. Use the Data List to check if the door key-linked lock and unlock switches are functioning properly (Click here).

      Table 3. Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Door Key SW-Lock Door key-linked switch lock signal / ON or OFF

      ON: Front door lock key cylinder turned to lock position

      OFF: Front door lock key cylinder not turned

      		 -
      Door Key SW-Unlock Door key-linked switch unlock signal / ON or OFF

      ON: Front door lock key cylinder turned to unlock position

      OFF: Front door lock key cylinder not turned

      		 -
      OK
      On tester screen, each item changes between ON and OFF according to above chart.

  5. Click here

    INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH)


    1. A01ISXNE13

      for LHD:


      1. Remove the front door lock LH (Click here).

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        9 (L) - 7 (E) Lock Below 1 Ω
        9 (L) - 7 (E) Off 10 kΩ or higher
        10 (UL) - 7 (E) Unlock Below 1 Ω
        10 (UL) - 7 (E) Off 10 kΩ or higher
    2. A01ISCGE01

      for RHD:


      1. Remove the front door lock RH (Click here).

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        5 (UL) - 8 (E) Unlock Below 1 Ω
        5 (UL) - 8 (E) Off 10 kΩ or higher
        6 (L) - 8 (E) Lock Below 1 Ω
        6 (L) - 8 (E) Off 10 kΩ or higher

  6. Click here

    CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK - MAIN BODY ECU AND BODY GROUND)


    1. A01ITR3E03

      for LHD:


      1. Disconnect the K9 door lock connector.

      2. Disconnect the DH ECU connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        K9-10 (UL) - DH-6 (UL2) Always Below 1 Ω
        K9-9 (L) - DH-7 (L2) Always Below 1 Ω
        K9-7 (E) - Body ground Always Below 1 Ω
        K9-10 (UL) - Body ground Always 10 kΩ or higher
        K9-9 (L) - Body ground Always 10 kΩ or higher
        Table 4. Text in Illustration
        *1

        Front view of wire harness connector

        (to Main Body ECU)
        *2

        Component without harness connected

        (to Front Door Lock)
    2. A01ITR3E04

      for RHD:


      1. Disconnect the J7 door lock connector.

      2. Disconnect the DH ECU connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        J7-5 (UL) - DH-6 (UL2) Always Below 1 Ω
        J7-6 (L) - DH-7 (L2) Always Below 1 Ω
        J7-8 (E) - Body ground Always Below 1 Ω
        J7-5 (UL) - Body ground Always 10 kΩ or higher
        J7-6 (L) - Body ground Always 10 kΩ or higher
        Table 5. Text in Illustration
        *1

        Front view of wire harness connector

        (to Main Body ECU)
        *2

        Component without harness connected

        (to Front Door Lock)

  7. Click here

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY IS DEFECTIVE)

  10. Click here

    REPLACE FRONT DOOR LOCK ASSEMBLYClick here