Click here

LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2324

Click here
Click here Click here
DTC Code DTC Name
B2324 Rear Door LH ECU Communication Stop
Click here

DESCRIPTION

This DTC is stored when LIN communication between the rear door window regulator LH and main body ECU (instrument panel junction block assembly) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2324 No communication between the rear door window regulator LH and main body ECU (instrument panel junction block assembly) for 10 seconds or more.

  • Rear door window regulator assembly LH

  • Main body ECU (instrument panel junction block assembly)

  • Harness or connector
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

  • When using the intelligent tester with the ignition switch off to troubleshoot:

    Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

  • Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

Tip:

When communication between the rear door window regulator LH and main body ECU (instrument panel junction block assembly) stops, DTC B2325 is also stored.

Click here

PROCEDURE


  1. Click here

    CLEAR DTC


    1. Clear the DTCs (Click here).


  2. Click here

    CHECK FOR DTC


    1. Check for DTCs (Click here).

      Table 1. Result
      Result Proceed to
      DTC B2324 is output A
      DTC B2324 is not output B

  3. Click here

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR DOOR WINDOW REGULATOR LH)


    1. A01ISZ2E09

      Disconnect the H79 ECU connector.

    2. Disconnect the M3 regulator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H79-23 (LIN2) - M3-9 (LIN) Always Below 1 Ω
      H79-23 (LIN2) - Body ground Always 10 kΩ or higher
      Table 2. Text in Illustration
      *1

      Front view of wire harness connector

      (to Main Body ECU)
      *2

      Front view of wire harness connector

      (to Rear Door Window Regulator LH)

  4. Click here

    CHECK HARNESS AND CONNECTOR (REAR DOOR WINDOW REGULATOR LH - BATTERY AND BODY GROUND)


    1. A01ITC9E09

      Disconnect the M3 regulator connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M3-1 (GND) - Body ground Always Below 1 Ω
      Standard Voltage
      Tester Connection Condition Specified Condition
      M3-2 (B) - Body ground Always 11 to 14 V
      Table 3. Text in Illustration
      *1

      Front view of wire harness connector

      (to Rear Door Window Regulator LH)

  5. Click here

    REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. Temporarily replace the rear door window regulator LH with a new or normally functioning one (Click here).

    2. Clear the DTCs (Click here).


  6. Click here

    CHECK FOR DTC


    1. Check for DTCs (Click here).

      Table 4. Result
      Result Proceed to
      DTC B2324 is not output A
      DTC B2324 is output B

  7. Click here

    USE SIMULATION METHOD TO CHECKClick here

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  10. Click here

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

  11. Click here

    END (REAR DOOR WINDOW REGULATOR LH IS DEFECTIVE)