ULTRASONIC SENSOR (for Rear) INSTALLATION


  1. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Align the slit of the No. 1 ultrasonic sensor retainer with the protrusion of the rear bumper cover and install the No. 1 ultrasonic sensor retainer.

    • Pay attention to the protrusions of the rear bumper cover as the orientation of the retainer changes depending on the installation position.

    • Use the same procedure for both No. 1 ultrasonic sensor retainers.

    A01IUQTE01
    Text in Illustration
    *1 Rear View of Rear Bumper - -

    1. A01IQCAE01
      Text in Illustration
      *1 Slit
      *2 Protrusion

      Attach the 4 claws to install the No. 1 ultrasonic sensor retainer to the rear bumper cover.

      Note

      Do not damage the bumper cover with the protrusion when installing the retainer.

  2. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Align the slit of the No. 2 ultrasonic sensor retainer with the protrusion of the rear bumper cover and install the No. 2 ultrasonic sensor retainer.

    • Use the same procedure for both No. 2 ultrasonic sensor retainers.

    A01IP07E01
    Text in Illustration
    *1 Rear View of Rear Bumper - -

    1. A01IQWME01
      Text in Illustration
      *1 Slit
      *2 Protrusion

      Attach the 3 claws to install the No. 2 ultrasonic sensor retainer to the rear bumper cover.

      Note

      Do not damage the bumper cover with the protrusion when installing the retainer.

  3. INSTALL NO. 1 ULTRASONIC SENSOR CLIP

    A01IOCU

    Tech Tips

    Use the same procedure for both No. 1 ultrasonic sensor clips.


    1. Attach the claw to install the No. 1 ultrasonic sensor clip.

  4. INSTALL NO. 2 ULTRASONIC SENSOR CLIP

    A01ITI2

    Tech Tips

    Use the same procedure for both No. 2 ultrasonic sensor clips.


    1. Attach the claw to install the No. 2 ultrasonic sensor clip.

  5. INSTALL NO. 1 ULTRASONIC SENSOR

    A01IRZT

    Tech Tips

    Use the same procedure for all ultrasonic sensors.


    1. Attach the 2 claws to install the ultrasonic sensor.

  6. INSTALL NO. 4 FLOOR WIRE


    1. When using a new rear bumper cover:

      Clean the rear bumper cover surface.

    2. When reusing the rear bumper cover:

      Wipe off any tape adhesive residue with cleaner.

    3. Attach the 4 clamps to install the No. 4 floor wire.

    4. Connect the 4 connectors.

    5. Install 4 new pieces of tape as shown in the illustration.

      Tech Tips

      Align the tape with the mark-off line of the rear bumper.

      A01IU7EE01
      Text in Illustration
      *1 Tape - -

  7. INSTALL REAR BUMPER COVER


    1. w/ TOYOTA Parking Assist-sensor System:

      Connect the No. 4 floor wire connector.

    2. Attach the 10 claws to install the rear bumper cover.

      A01IN3C

    3. Install the 5 clips and 2 bolts.

      A01IS8H
    4. A01IMZC

      Install the screw.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  8. INSTALL NO. 1 FLOOR UNDER COVER


    1. A01ISJG

      Install the No. 1 floor under cover with the 5 clips.