Click here

TOYOTA PARKING ASSIST-SENSOR SYSTEM Clearance Sonar Main Switch Circuit

Click here
Click here Click here
DTC Code DTC Name
  Clearance Sonar Main Switch Circuit
Click here

DESCRIPTION

When the back sonar or clearance sonar switch assembly turns on, the on signal is input into the ECU.

A01INCCE01
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Click here

PROCEDURE


  1. Click here

    CHECK SYMPTOMS


    1. Check the symptoms.

      Table 1. Result
      Result Proceed to
      Back sonar or clearance sonar switch does not operate normally A
      Back sonar or clearance sonar switch operate normally, but the switch indicator does not illuminate A
      Back sonar or clearance sonar switch operate normally, but the indicator does not illuminate normally B

  2. Click here

    INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY


    1. A01ISEZE07

      Remove the back sonar or clearance sonar switch assembly (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      3 (ECU) - 6 (IG) Sonar switch on Below 1 Ω
      3 (ECU) - 6 (IG) Sonar switch off 10 kΩ or higher

    3. Inspect the indicator operation.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 3 (ECU)

      Battery negative (-) → Terminal 7 (E)

      		 LED illuminates
      Table 2. Result
      Result Proceed to
      OK (except 1WW Engine) A
      OK (for 1WW Engine) B
      NG C

  3. Click here

    CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - BATTERY)


    1. A01ISVPE10

      Disconnect the H97 back sonar or clearance sonar switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H97-6 (IG) - Body ground Ignition switch ON 11 to 14 V
      H97-6 (IG) - Body ground Ignition switch off Below 1 V
      Table 3. Text in Illustration
      *a

      Front view of wire harness connector

      (to Back Sonar or Clearance Sonar Switch Assembly)

  4. Click here

    CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - CLEARANCE WARNING ECU)


    1. Disconnect the H97 back sonar or clearance sonar switch assembly connector.

    2. Disconnect the H95 clearance warning ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-3 (ECU) - H95-1 (IG) Always Below 1 Ω
      H97-7 (E) - H95-25 (MSDL) Always Below 1 Ω
      H97-3 (ECU) - Body ground Always 10 kΩ or higher
      H97-7 (E) - Body ground Always 10 kΩ or higher

  5. Click here

    CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - STOP AND START ECU)


    1. Disconnect the H97 back sonar or clearance sonar switch assembly connector.

    2. Disconnect the H121 stop and start ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-6 (IG) - H121-12 (IGO1) Always Below 1 Ω
      H97-6 (IG) - Body ground Always 10 kΩ or higher

  6. Click here

    CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - CLEARANCE WARNING ECU)


    1. Disconnect the H97 back sonar or clearance sonar switch assembly connector.

    2. Disconnect the H95 clearance warning ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-3 (ECU) - H95-1 (IG) Always Below 1 Ω
      H97-7 (E) - H95-25 (MSDL) Always Below 1 Ω
      H97-3 (ECU) - Body ground Always 10 kΩ or higher
      H97-7 (E) - Body ground Always 10 kΩ or higher

  7. Click here

    INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY


    1. A01ISEZE08

      Remove the back sonar or clearance sonar switch assembly (Click here).

    2. Inspect the indicator operation.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 5 (ILL+)

      Battery negative (-) → Terminal 4 (ILL-)

      		 LED illuminates

  8. Click here

    CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH - BATTERY)


    1. A01ISVPE13

      Disconnect the H97 back sonar or clearance sonar switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H97-5 (ILL+) - Body ground Ignition switch ON, light control switch tail or head 11 to 14 V
      H97-5 (ILL+) - Body ground Ignition switch off, light control switch off Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H97-4 (ILL-) - Body ground Always Below 1 Ω
      Table 4. Text in Illustration
      *a

      Front view of wire harness connector

      (to Back Sonar or Clearance Sonar Switch Assembly)

  9. Click here

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

  10. Click here

    REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLYClick here

  11. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. Click here

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here