STEREO JACK ADAPTER ASSEMBLY REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. Click here.

  2. REMOVE BATTERY SERVICE HOLE COVER


    1. A01ITOM

      Remove the clip and battery service hole cover.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

    A01IRZYE01
    Text in Illustration
    *1 Protective Tape

    1. for Automatic Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips and 2 guides, and remove the instrument panel finish panel end.

    2. A01IQ6AE01
      Text in Illustration
      *1 Protective Tape

      for Manual Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips and guide, and remove the instrument panel finish panel end.

  5. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

    A01IU46E01
    Text in Illustration
    *1 Protective Tape

    1. for Automatic Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips, claw and 2 guides, and remove the instrument panel finish panel end.

    2. A01IQX3E01
      Text in Illustration
      *1 Protective Tape

      for Manual Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

      2. Using a moulding remover, detach the 3 clips, claw and guide, and remove the instrument panel finish panel end.

  6. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

    A01IQZA

    1. Detach the 8 claws and 4 guides.

    2. Disconnect the connector and remove the center instrument panel register.

  7. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


    1. A01ITOZ

      Remove the 4 screws.

    2. A01IOQ4

      Pull the radio receiver to detach the 4 clips on the backside of the radio receiver with bracket.

    3. Disconnect the connectors and remove the radio receiver with bracket.

  8. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Radio Receiver)


    1. A01IQAW

      Remove the 4 screws.

    2. A01IRVG

      Pull out the radio and display receiver assembly with bracket.

    3. Disconnect the connectors and remove the radio radio and display receiver assembly with bracket.

  9. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Audio)

    A01IRZ3

    1. Detach the 4 clips, 3 claws and 3 guides, and remove the center instrument cluster finish panel.

  10. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Audio)

    A01ISEY

    1. Remove the 4 bolts and stereo opening cover.

  11. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. Twist the shift lever knob in the direction indicated by the arrow and remove it.

      A01ISYGE01

  12. REMOVE SHIFTING HOLE COVER (for Manual Transaxle)

    A01IOOWE01
    Text in Illustration
    *1 T Washer

    1. Twist the T washer in the direction indicated by the arrow and remove it.

    2. Remove the knob spring.

    3. Detach the 5 claws and 3 clips, and remove the shifting hole cover.

  13. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (except Manual Transaxle)

    A01IROS

    1. Detach the 5 claws and 3 clips.

    2. Disconnect the connector and remove the position indicator housing.

  14. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (except Manual Transaxle)

    A01ITJ5

    1. for Automatic Air Conditioning System:


      1. Remove the 3 screws <C>.

      2. Detach the 2 claws, 4 clips and 5 guides, and remove the lower center instrument panel finish panel.

        Tech Tips

        If the 2 claws shown in the illustration are difficult to detach, detach the 4 clips of the air conditioning control and remove the lower center instrument panel finish panel together with the air conditioning control.

    2. A01IOIV

      for Manual Air Conditioning System:


      1. Remove the 3 screws <C>.

      2. Detach the 4 clips, 2 claws and 5 guides, and remove the lower center instrument panel finish panel.

  15. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (for Manual Transaxle)

    A01IOJM

    1. for Automatic Air Conditioning System:


      1. Remove the 2 screws <C>.

      2. Detach the 2 claws, 4 clips and 5 guides, and remove the lower center instrument panel finish panel.

        Tech Tips

        If the 2 claws shown in the illustration are difficult to detach, detach the 4 clips of the air conditioning control and remove the lower center instrument panel finish panel together with the air conditioning control.

    2. A01IN3V

      for Manual Air Conditioning System:


      1. Remove the 2 screws <C>.

      2. Detach the 4 clips, 2 claws and 5 guides, and remove the lower center instrument panel finish panel.

  16. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    1. Detach the 3 claws and guide, and remove the front No. 1 console box insert.

      A01IUSGE01

  17. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. Detach the 3 claws and guide, and remove the front No. 2 console box insert.

      A01IQC5E01

  18. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A01IPGW

    1. Remove the screw <D>.

    2. Disconnect the connector.

    3. Detach the 4 clips and remove the lower No. 1 instrument panel finish panel.

  19. REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY


    1. A01IS8Q

      Disconnect the connector.

    2. A01IS6H

      Detach the 2 claws and remove the stereo jack adapter.