Click here

RADIO RECEIVER REMOVAL

Click here
Click here Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here).

  2. Click here

    REMOVE BATTERY SERVICE HOLE COVER


    1. A01ITOM

      Remove the clip and battery service hole cover.

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  4. Click here

    REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. for Automatic Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

        Table 1. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover, detach the 3 clips and 2 guides, and remove the instrument panel finish panel end.

    2. A01IQ6AE01

      for Manual Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

        Table 2. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover, detach the 3 clips and guide, and remove the instrument panel finish panel end.

  5. Click here

    REMOVE INSTRUMENT PANEL FINISH PANEL END RH


    1. for Automatic Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

        Table 3. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover, detach the 3 clips, claw and 2 guides, and remove the instrument panel finish panel end.

    2. A01IQX3E01

      for Manual Air Conditioning System:


      1. Put protective tape around the instrument panel finish panel end.

        Table 4. Text in Illustration
        *1 Protective Tape

      2. Using a moulding remover, detach the 3 clips, claw and guide, and remove the instrument panel finish panel end.

  6. Click here

    REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Detach the 8 claws and 4 guides.

    2. Disconnect the connector and remove the center instrument panel register.

  7. Click here

    REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)


    1. A01ITOZ

      Remove the 4 screws.

    2. A01IOQ4

      Pull the radio receiver to detach the 4 clips on the backside of the radio receiver with bracket.

    3. Disconnect the connectors and remove the radio receiver with bracket.

  8. Click here

    REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for Radio and Display Type)


    1. Detach the 4 clips, 3 claws and 3 guides, and remove the center instrument cluster finish panel.

  9. Click here

    REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)


    1. A01IQAW

      Remove the 4 screws.

    2. A01IRVG

      Pull out the radio and display receiver assembly with bracket.

    3. Disconnect the connectors and remove the radio radio and display receiver assembly with bracket.

  10. Click here

    REMOVE NO. 1 RADIO BRACKET (for Radio Receiver Type)


    1. A01IUCG

      Remove the 3 screws and No. 1 radio bracket.

  11. Click here

    REMOVE NO. 1 RADIO BRACKET (for Radio and Display Type)


    1. A01IU6A

      Remove the 3 screws and No. 1 radio bracket.

  12. Click here

    REMOVE NO. 2 RADIO BRACKET (for Radio Receiver Type)


    1. A01IRUQ

      Remove the 3 screws and No. 2 radio bracket.

  13. Click here

    REMOVE NO. 2 RADIO BRACKET (for Radio and Display Type)


    1. A01IQHK

      Remove the 3 screws and No. 2 radio bracket.