Click here

HEADLIGHT CLEANER ACTUATOR INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH


    1. A01IST4

      Attach the 2 claws to install the headlight washer actuator sub-assembly LH.

    2. A01ISQQ

      Install the 2 screws.

  2. Click here

    INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  3. Click here

    INSTALL HEADLIGHT WASHER HOSE


    1. A01IPAW

      Attach the 6 clamps to install the hose to the front bumper.

    2. Connect the headlight washer hose to the headlight washer actuator sub-assemblies.

  4. Click here

    INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH


    1. Extend the type 1 headlight washer nozzle sub-assembly LH by hand.

    2. A01IQQT

      Attach the claw to install the type 1 headlight washer nozzle sub-assembly LH.

  5. Click here

    INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH

    Tip:

    Use the same procedure described for the LH side.

  6. Click here

    INSTALL FRONT BUMPER COVER


    1. Install the front bumper cover (Click here).

  7. Click here

    PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light)


    1. Prepare the vehicle.

      Table 1. Text in Illustration
      *a 25 m or 3 m

      • Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

      • Place the vehicle at a 90° angle to the wall.

      • Create a 25 m (82 ft.) distance between the vehicle (fog light bulb center) and the wall.

      • Make sure that the vehicle is on a level surface.

      • Bounce the vehicle up and down to settle the suspension.

        Note:

        A distance of 25 m (82 ft.) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration.)

    2. Prepare a piece of thick white paper approximately 2.0 m (6.56 ft.) (height) x 4.0 m (13.1 ft.) (width) to use as a screen.

    3. Draw a vertical line down the center of the screen (V line).

    4. Set the screen as shown in the illustration.

      Tip:

      • Stand the screen perpendicular to the ground.

      • A01IP8NE01

        Align the V line on the screen with the center of the vehicle.

    5. A01IT6FE01

      Draw base lines (H, V LH and V RH lines) on the screen as shown in the illustration.

      Table 2. Text in Illustration
      *a V LH Line
      *b V Line
      *c V RH Line
      *d H Line
      *e Ground
      Tip:

      Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


      1. H Line (Fog light height):

        Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.

      2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):

        Draw 2 vertical lines so that they intersect the H line at each center mark.

  8. Click here

    INSPECT FOG LIGHT AIMING (w/ Fog Light)


    1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

      Note:

      Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

    2. Start the engine.

    3. A01IUS7E46

      Turn on the fog light and check if the cutoff line falls within the specified area in the following illustration.

      Tip:

      • If the alignment distance is 25 m (82 ft.):

        The upper edge of the hot zone for the fog light should be 375 mm (14.8 in.) below the H line.

      • If the alignment distance is 3 m (9.84 ft.):

        The upper edge of the hot zone for the fog light should be 45 mm (1.77 in.) below the H line.

  9. Click here

    ADJUST FOG LIGHT AIMING (w/ Fog Light)


    1. Adjust the aim vertically.

      Table 3. Text in Illustration
      *1 Aiming Screw

      Adjust the aim of each fog light to the specified range by turning the aiming screw with a screwdriver.

      Note:

      The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.

      Tip:

      If it is not possible to correctly adjust fog light aim, check the bulb, fog light unit and fog light unit reflector installation.