Click here

FRONT WIPER MOTOR INSTALLATION

Click here
Click here Click here
Tip:

  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here
  1. Click here

    INSTALL WIPER MOTOR WIRE


    1. A01IS5O

      Attach the claw to install the wiper motor wire.

  2. Click here

    INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY


    1. A01IRCK

      Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.

      7.5 N*m 76 kgf*cm 66 in.*lbf

    2. Connect the connector.

  3. Click here

    INSTALL FRONT WIPER CRANK SUB-ASSEMBLY


    1. Check the automatic stop position.


      1. for LHD:

        Check that the motor stops automatically at the automatic stop position (Click here).

      2. for RHD:

        Check that the motor stops automatically at the automatic stop position (Click here).

    2. When installing a new windshield wiper motor:


      1. A01ITOUE01

        Install the front wiper crank sub-assembly to the front wiper motor assembly with the nut so that center lines of the crank arm spring and wiper link stay are parallel.

        Tip:

        Hold the front wiper crank sub-assembly by hand when tightening the nut.

        Table 1. Text in Illustration
        *1 Center Line of Wiper Link Stay
        *2 Center Line of Crank Arm Spring
        17 N*m 173 kgf*cm 13 ft.*lbf

    3. When reusing the windshield wiper motor:


      1. A01IRS9E01

        Install the front wiper crank with the nut so that the matchmarks on the wiper motor, front wiper crank and nut are aligned.

        Tip:

        Hold the front wiper crank sub-assembly by hand when tightening the nut.

        17 N*m 173 kgf*cm 13 ft.*lbf
        Table 2. Text in Illustration
        *1 Front Wiper Crank Sub-assembly
    4. A01ISHME01

      Apply MP grease to the front wiper crank pivot of the windshield wiper motor assembly.

    5. A01IQBW

      Connect the rod of the wiper link to the front wiper crank.

  4. Click here

    INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY


    1. A01ISAD

      Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body and install the wiper motor and link.

    2. A01ITHG

      Install the 2 bolts.

      5.5 N*m 56 kgf*cm 49 in.*lbf
    3. A01IQJZ

      Connect the connector and attach the clamp to install the wire harness to the cowl top panel.

  5. Click here

    INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01IQI1

      Attach the 4 claws and 5 guides to install the cowl top ventilator louver RH.

    2. Install the clip.

  6. Click here

    INSTALL COWL TOP VENTILATOR LOUVER LH


    1. A01IPRQ

      Attach the 6 claws and 5 guides to install the cowl top ventilator louver LH.

    2. Install the clip.

    3. A01INVH

      Attach the 2 claws and 2 guides to install the center cowl top ventilator louver.

  7. Click here

    INSTALL HOOD TO COWL TOP SEAL


    1. A01IQHZ

      Attach the 7 clips and 2 claws to install the hood to cowl top seal.

  8. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  9. Click here

    INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A01ITA3E01

      Clean the wiper arm serrations.

      Table 3. Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A01ITNDE01

      Position the blade tip within the range shown in the illustration.

      Tip:

      The lower limit of the range is indicated by the mark on the glass.

      Table 4. Text in Illustration
      *1 Mark for Blade Position

    5. Install the front wiper arm and blade assembly RH with the nut.

      26 N*m 265 kgf*cm 19 ft.*lbf
      Tip:

      Hold the arm hinge by hand when tightening the nut.

  10. Click here

    INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.

    2. A01ITA3E01

      Clean the wiper arm serrations.

      Table 5. Text in Illustration
      *1 Wiper Arm Serrations
      *2 Wire Brush
      *3 Wiper Pivot Serrations

    3. When reusing the front wiper motor and link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    4. A01ITAIE01

      Position the blade tip within the range shown in the illustration.

      Tip:

      The lower limit of the range is indicated by the mark on the glass.

      Table 6. Text in Illustration
      *1 Mark for Blade Position

    5. Install the front wiper arm and blade assembly LH with the nut.

      26 N*m 265 kgf*cm 19 ft.*lbf
      Tip:

      Hold the arm hinge by hand when tightening the nut.

    6. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

  11. Click here

    INSTALL FRONT WIPER ARM HEAD CAP


    1. A01ISR6

      Install the front wiper arm head cap.

      Tip:

      Use the same procedure for all front wiper arm head caps.