OUTER REAR VIEW MIRROR INSPECTION


  1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

    A01IPD6E01
    Text in Illustration
    *1

    Component without harness connected

    (Outer Rear View Mirror LH)

    1. Apply battery voltage and check the operation of the mirror.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 1 (MV)

      Battery negative (-) → Terminal 2 (M+)

      		 Turns upward (A)

      Battery negative (-) → Terminal 1 (MV)

      Battery positive (+) → Terminal 2 (M+)

      		 Turns downward (B)

      Battery positive (+) → Terminal 3 (MH)

      Battery negative (-) → Terminal 2 (M+)

      		 Turns left (C)

      Battery negative (-) → Terminal 3 (MH)

      Battery positive (+) → Terminal 2 (M+)

      		 Turns right (D)

      If the result is not as specified, replace the outer rear view mirror assembly.

    2. A01IOFZE01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror LH)

      Check the mirror heater.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Terminal 5 (+) - Terminal 4 (-) 25°C (77°F) 5.0 to 7.0 Ω

        If the result is not as specified, replace the outer rear view mirror assembly.

      2. Apply battery voltage and check the operation of the mirror heater.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 5 (+)

        Battery negative (-) → Terminal 4 (-)

        		 Mirror becomes warm

        Tech Tips

        It will take a short amount of time for the mirror to become warm.

        If the result is not as specified, replace the outer rear view mirror assembly.

  2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

    A01IQHWE01
    Text in Illustration
    *1

    Component without harness connected

    (Outer Rear View Mirror RH)

    1. Apply battery voltage and check the operation of the mirror.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 1 (MV)

      Battery negative (-) → Terminal 2 (M+)

      		 Turns upward (A)

      Battery negative (-) → Terminal 1 (MV)

      Battery positive (+) → Terminal 2 (M+)

      		 Turns downward (B)

      Battery positive (+) → Terminal 3 (MH)

      Battery negative (-) → Terminal 2 (M+)

      		 Turns left (C)

      Battery negative (-) → Terminal 3 (MH)

      Battery positive (+) → Terminal 2 (M+)

      		 Turns right (D)

      If the result is not as specified, replace the outer rear view mirror assembly.

    2. A01INOOE01
      Text in Illustration
      *1

      Component without harness connected

      (Outer Rear View Mirror RH)

      Check the mirror heater.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Terminal 5 (+) - Terminal 4 (-) 25°C (77°F) 5.0 to 7.0 Ω

        If the result is not as specified, replace the outer rear view mirror assembly.

      2. Apply battery voltage and check the operation of the mirror heater.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 5 (+)

        Battery negative (-) → Terminal 4 (-)

        		 Mirror becomes warm

        Tech Tips

        It will take a short amount of time for the mirror to become warm.

        If the result is not as specified, replace the outer rear view mirror assembly.