REAR DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

    A01IPDH

    1. Attach the 8 claws to install the rear door belt moulding.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    1. w/ Power Window:


      1. Temporarily install the regulator switch assembly.

      2. Connect the cable to the negative (-) battery terminal.

      3. Operate the regulator switch until the regulator reaches its bottom dead center.

      4. Disconnect the cable from the negative (-) battery terminal.

        Note

        When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

      5. Remove the regulator switch assembly.

    2. w/o Power Window:


      1. Temporarily install the rear door window regulator handle assembly.

      2. Turn the handle until the regulator reaches its bottom dead center.

      3. Remove the rear door window regulator handle assembly.

    3. A01IQGG

      Install the front side of the glass run.

    4. A01IS5SE02

      Apply MP grease to the sliding areas of the glass channel as shown in the illustration.

      Standard
      Area Specified Condition
      A 130 mm (5.12 in.)
      B 29 mm (1.14 in.)
    5. A01IOSY

      Slide the rear door glass sub-assembly as shown in the illustration to install it.

  3. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A01ITDR

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A01IT1R

      Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door window division bar sub-assembly to the glass run.

    3. A01ISN0

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

      Torque:
      6.2 N*m  { 63 kgf*cm, 55 in.*lbf, for bolt and screw }

  5. INSTALL REAR DOOR GLASS RUN LH


    1. A01IS5C

      Completely install the glass run.

  6. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply butyl tape to the door.

    2. A01IQJEE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

    3. Install the rear door service hole cover by using the reference points on the rear door panel.

      Note


      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the seal quality.

    4. Connect the connector.

  7. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A01ITY6

      Install the rear door inner glass weatherstrip to the door panel.

  8. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A01ISMJ

      Connect the 2 cables to the inside handle to install the inside handle.

  9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01IODC

      Install the clamp to the door panel.

    2. A01IO4S

      Attach the 2 claws to install the inside handle to the rear door trim board.

    3. A01IQESE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Attach the rear door trim board with the 4 claws on the rear door inner glass weatherstrip.

    4. A01IP0B

      Install the rear door trim board with the 10 clips.

    5. Install the 3 screws.

  10. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)


    1. Connect the connector.

    2. A01IREP

      Attach the 4 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  11. INSTALL REAR DOOR TRIM MOULDING LH


    1. A01IR9Q

      Attach the 8 claws to install the door trim moulding.

  12. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH


    1. A01IT23

      Attach the 3 claws to install the rear door inside handle bezel.

  13. INSTALL REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Install the rear door regulator inside handle plate.

  14. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. Temporarily install the rear door window regulator handle assembly, fully close the window, and then remove the rear door window regulator handle assembly.

    2. Install the snap ring to the rear door window regulator handle assembly.

    3. A01IR9XE01
      Text in Illustration
      *1 Front Side

      Install the rear door window regulator handle assembly as shown in the illustration.

      Standard
      Area Specified Condition
      A 50° to 60°

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.