FRONT DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

    A01IREJ

    1. Attach the 6 claws to install the front door belt moulding.

    2. Install the clip.

  2. INSTALL FRONT DOOR GLASS RUN LH


    1. A01IQYV

      Install the front door glass run.

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. for Driver Side:

      Temporarily install the master switch assembly.

    2. for Front Passenger Side:

      Temporarily install the regulator switch assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Move the door glass until the bolts appear in the service holes.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    6. A01IT9B

      Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

      Note

      Be careful not to damage the glass.

    7. Install the door glass to the window regulator with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  4. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. Apply butyl tape to the door.

    2. Pass the front door lock remote control cable and front door inside locking cable through a new front door service hole cover.

    3. A01INRGE01
      Text in Illustration
      *1 Reference Point

      Install the front door service hole cover according to the reference points on the front door panel.

      Note


      • Securely install the front door service hole cover to prevent wrinkles and air bubbles.

      • There should be no wrinkles or folds after installing the service hole cover.

      • After installing the service hole cover, check the seal quality.

    4. A01IOWT

      Connect the 2 connectors.

  5. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A01INVC

      Install the front door inner glass weatherstrip.

  6. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A01IOHC

      Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly to install the inside handle.

  7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01IUHM

      Attach the 2 claws to install the front door inside handle sub-assembly to the door trim board.

    2. A01IS0O

      Attach the front door trim board with the 5 claws of the front door inner glass weatherstrip and the reference boss.

    3. w/ Courtesy Light:


      1. Connect the courtesy light connector.

    4. A01IR1B

      Attach the 9 clips to install the trim board.

    5. Install the 3 screws.

  8. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

    A01IOY9E01

    1. Connect the connector.

    2. Attach the 7 claws and clip to install the power window regulator master switch assembly with front door armrest base panel.

  9. INSTALL FRONT DOOR TRIM MOULDING LH


    1. A01IPP4

      Attach the 8 claws to install the front door trim moulding.

  10. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH


    1. A01IRBS

      Attach the 3 claws to install the inside handle bezel.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.