TIRE PRESSURE WARNING SYSTEM, Diagnostic DTC:C2174/74, C2191/91

DTC Code DTC Name
C2174/74 Vehicle Speed Signal Malfunction
C2191/91 Vehicle Speed Signal Error (Test Mode DTC)

DESCRIPTION

Speeds signals are sent from the combination meter assembly to the tire pressure warning ECU and receiver.

DTC C2191/91 is stored only during the signal check.

DTC Code Detection Condition Trouble Area
C2174/74

All conditions below are met:


  • DTC C2121/21, C2122/22, C2123/23, and/or C2124/24 is output

  • Vehicle speed signal malfunction

  • Combination meter

  • Vehicle speed signal circuit

  • Harness or connector

  • Tire pressure warning ECU and receiver

  • Tire pressure warning valve and transmitter
C2191/91 Test mode procedure is performed.

  • Meter / gauge system (speed signal)

  • Vehicle speed signal circuit

  • Harness or connector

  • Tire pressure warning ECU and receiver

WIRING DIAGRAM

A01INR7E01

INSPECTION PROCEDURE

Note


  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

  • It is necessary to perform initialization Click here after registration Click here of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.

Tech Tips

When the speedometer needle is not moving, first troubleshoot the meter/gauge system Click here.

PROCEDURE


  1. READ VALUE USING GTS (VEHICLE SPEED)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

    6. Check that the values indicated on the GTS and on the combination meter assembly are the same.

      Tire Pressure Monitor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Vehicle Speed

      Vehicle speed/

      min.: 0 km/h (0 mph)

      max.: 255 km/h (158 mph)

      		 Actual vehicle speed Speed indicated on combination meter assembly
      OK
      Vehicle speed indicated on the GTS indicates the actual speed.

    NG

    CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER ASSEMBLY) Click here

    OK

  2. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Turn the ignition switch off.

    3. Turn the ignition switch to ON.

    4. Perform a driving test.

    5. Check for DTCs Click here.

      Tech Tips

      The time required for DTC C2174 to be stored is 20 minutes.

      Result
      Result Proceed to
      DTC C2174/74 is not output A
      DTC C2174/74 is output B

    B

    REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER Click here

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

  3. CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER ASSEMBLY)


    1. Disconnect the tire pressure warning ECU and receiver N32 connector.

    2. Disconnect the combination meter assembly H62 connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N32-2 (SPD) - H62-3 (+S) Always Below 1 Ω
      N32-2 (SPD) or H62-3 (+S) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)


    1. Disconnect the skid control ECU (brake actuator assembly) A52*1 or A54*2 connector.


      • *1: except ZR Series Engine

      • *2: for ZR Series Engine

    2. Disconnect the combination meter assembly H62 connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      except ZR Series Engine
      Tester Connection Condition Specified Condition
      A52-33 (SP1) - H62-5 (SI) Always Below 1 Ω
      A52-33 (SP1) or H62-5 (SI) - Body ground Always 10 kΩ or higher
      for ZR Series Engine
      Tester Connection Condition Specified Condition
      A54-33 (SP1) - H62-5 (SI) Always Below 1 Ω
      A54-33 (SP1) or H62-5 (SI) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK DTC OUTPUT


    1. Check for DTCs.

      Tech Tips


      Result
      Result Proceed to
      DTC P0500 is not output A
      DTC P0500 is output B

    B

    GO TO METER / GAUGE SYSTEM Click here

    A

  6. REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER


    1. Replace the tire pressure warning ECU and receiver Click here.


    NEXT

  7. PERFORM REGISTRATION OF TRANSMITTER ID


    1. Perform registration Click here.


    NEXT

  8. PERFORM INITIALIZATION


    1. Perform initialization Click here.


    NEXT

  9. CHECK TEST MODE DTC (C2191/91)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

    6. Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

      Result
      Result Proceed to
      DTC C2191 is not cleared A
      DTC C2191 is cleared B

    B

    END

    A

    GO TO DTC C2121/21 TO C2124/24 Click here