CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM, Diagnostic DTC:P2716

DTC Code DTC Name
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

DESCRIPTION

The ECM uses signals to control shift solenoid valve SLT to provide optimum line pressure control. Shift solenoid valve SLT is also used during forward and reverse clutch engagement to control the oil pressure to the forward and reverse clutch.

DTC Code

DTC Detection Condition


  1. Diagnosis Condition

  2. Malfunction Status

  3. Malfunction Time

  4. Other

 Trouble Area
P2716

  1. The vehicle is being driven.

  2. There is an open or short circuit in the shift solenoid valve SLT circuit.

  3. 1 second or more

  4. 1 trip detection logic

  • Open or short in shift solenoid valve SLT circuit

  • Continuously variable transaxle assembly

  • ECM

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the shift solenoid valve SLT circuit. When there is an open or short circuit in the shift solenoid valve SLT circuit, the ECM detects the problem, illuminates the MIL and stores the DTC.

WIRING DIAGRAM

A01ISJBE06

INSPECTION PROCEDURE

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)


    1. A01IPWEE09
      Text in Illustration
      *1

      Component without harness connected

      (Transmission Wire)

      Disconnect the transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SLT+) - 7 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
      2 (SLT+) - Body ground Always 10 kΩ or higher
      7 (SLT-) - Body ground Always 10 kΩ or higher

    NG

    Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. A01IUJYE45
      Text in Illustration
      *1

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C68-60 (SLT-) - C68-61 (SLT+) 20°C (68°F) 5.0 to 5.6 Ω
      C68-60 (SLT-) - Body ground Always 10 kΩ or higher
      C68-61 (SLT+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  4. PERFORM INITIALIZATION

    Note


    • Performing reset memory will clear the learned values of both the yaw rate sensor (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:

      Replaced Part

      • Continuously variable transaxle assembly

      • ECM

      • Oil pressure sensor

      • Yaw rate sensor

    • After performing reset memory, always perform yaw rate sensor (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.

    • Always perform 0 point calibration with the vehicle on level ground.

    • Do not shake or vibrate the vehicle during 0 point calibration.


    1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration Click here.

    2. Check that no DTC is stored.


    NEXT

    END

  5. REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY


    1. Replace the continuously variable transaxle assembly Click here.


    NEXT

  6. PERFORM INITIALIZATION

    Note


    • Performing reset memory will clear the learned values of both the yaw rate sensor (deceleration sensor 0 point calibration) and CVT oil pressure (CVT oil pressure calibration). Make sure to perform reset memory, yaw rate sensor 0 point calibration and CVT oil pressure calibration when replacing any of the parts shown in the following table:

      Replaced Part

      • Continuously variable transaxle assembly

      • ECM

      • Oil pressure sensor

      • Yaw rate sensor

    • After performing reset memory, always perform yaw rate sensor (deceleration sensor 0 point) calibration first, and then CVT oil pressure calibration.

    • Always perform 0 point calibration with the vehicle on level ground.

    • Do not shake or vibrate the vehicle during 0 point calibration.


    1. Using the intelligent tester, perform reset memory, deceleration sensor 0 point calibration and CVT oil pressure calibration Click here.

    2. Check that no DTC is stored.


    NEXT

    END