MANUAL TRANSAXLE ASSEMBLY INSTALLATION

Note

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


  1. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY


    1. A01IO87

      Coat a new O-ring with gear oil.

    2. Install the O-ring to the speedometer driven hole cover sub-assembly.

    3. Install the speedometer driven hole cover sub-assembly to the transaxle case with the bolt.

      Torque:
      11 N*m  { 115 kgf*cm, 8 ft.*lbf }

  2. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY


    1. A01IR6L

      Temporarily install the clutch release cylinder to bleeder tube to a new clutch release with bearing cylinder assembly.

    2. Clean and degrease all installation surfaces for the clutch release with bearing cylinder assembly.

    3. A01IU7F

      Install the clutch release with bearing cylinder assembly with 3 new bolts.

      Torque:
      23 N*m  { 229 kgf*cm, 17 ft.*lbf }

      Note


      • The clutch release with bearing cylinder and installation bolts cannot be reused and must be replaced with new ones.

      • Clean and degrease all installation surfaces and make sure the clutch release with bearing cylinder fits securely with the transaxle during installation. The first bolt should be tightened by hand while holding the clutch release with bearing cylinder.

      • Make sure that none of the clutch spline grease adheres to the clutch release with bearing cylinder.

      • The clutch release with bearing cylinder cannot be disassembled.

    4. A01IU6K

      Install the clutch tube boot to the manual transaxle assembly.

    5. A01INUU

      Temporarily install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

    6. Temporarily install the clutch release bleeder sub-assembly with the 2 bolts.

    7. A01ITOK

      Using a union nut wrench, install the clutch release cylinder to bleeder tube to the clutch release with bearing cylinder assembly.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

    8. A01ISD2E02
      Text in Illustration
      *1 Clutch spline grease

      Apply clutch spline grease to the input shaft spline.

      Grease
      Toyota Genuine Clutch Spline Grease or equivalent

  3. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY


    1. A01INUU

      Temporarily install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

    2. Install the clutch release bleeder sub-assembly with the 2 bolts.

      Torque:
      17 N*m  { 170 kgf*cm, 12 ft.*lbf }

    3. Using a union nut wrench, install the clutch release cylinder to bleeder tube.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

  4. INSPECT CLUTCH PIPE LINE

    A01IQJWE01

    1. Using SST, apply a pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

      SST
      09992-00242

      If the pressure drops, replace the clutch release cylinder to bleeder tube.

  5. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY


    1. A01INUU

      Temporarily install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

    2. Install the clutch release bleeder sub-assembly with the 2 bolts.

      Torque:
      17 N*m  { 170 kgf*cm, 12 ft.*lbf }

    3. Using a union nut wrench, install the clutch release cylinder to bleeder tube.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

  6. INSTALL CLUTCH FLEXIBLE HOSE BRACKET


    1. A01IPYR

      Install the clutch flexible hose bracket to the manual transaxle with the bolt.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  7. INSTALL CLUTCH RELEASE BLEEDER TO FLEXIBLE HOSE TUBE

    A01IQTQ

    1. Using a union nut wrench, install the clutch release bleeder to flexible hose tube to the clutch release bleeder sub-assembly.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note

      Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

    2. Install the 2 clamps to the manual transaxle with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  8. INSTALL REAR ENGINE MOUNTING BRACKET


    1. A01IPV1

      Install the rear engine mounting bracket with the 4 bolts.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

  9. INSTALL ENGINE MOUNTING BRACKET LH


    1. A01IOCY

      Apply adhesive to the 4 bolts.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    2. Install the engine mounting bracket LH with the 4 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  10. INSTALL FRONT ENGINE MOUNTING BRACKET


    1. A01INHF

      Install the front engine mounting bracket with the 4 bolts.

      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  11. INSTALL MANUAL TRANSAXLE ASSEMBLY


    1. A01INS9

      Align the input shaft with the clutch disc and install the manual transaxle to the engine.

      Note


      • Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle onto the engine with the contact surfaces of the engine and transaxle flat against each other.

      • Insert the dowel pins into the dowel holes securely so that the end face of the transaxle assembly fits close against the engine assembly before tightening the bolts.

    2. A01ITHU

      Install the 7 bolts.

      Torque:
      for Flange Bolt
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      for Bolt with Washer
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }
    3. A01IS0I

      Install the clamp and wire harness to the manual transaxle with the bolt.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }
    4. A01ITFU

      Connect the back-up light switch connector and install the wire harness to the manual transaxle with the bolt.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

  12. INSTALL ENGINE WIRE


    1. A01IS2Q

      Install the engine wire with the 2 bolts.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

  13. INSTALL STARTER ASSEMBLY


    1. Install the starter assembly Click here.

  14. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


    1. Install the engine assembly with transaxle Click here.