Click here

CRUISE CONTROL SYSTEM (except 1WW) DATA LIST / ACTIVE TEST

Click here
Click here Click here
Click here
  1. DATA LIST

    Tip:

    Using the intelligent tester to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Cruise Control / Data List.

    5. According to the display on the intelligent tester, read the Data List.

      Table 1. Cruise Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      CCS Vehicle Spd Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Actual vehicle speed displayed -
      CCS Mem Vehicle Spd Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph) Vehicle speed stored in memory -
      Throttle Opening Angle Required throttle opening angle / Min.: 0 deg, Max.: 124.4 deg Required throttle opening angle -
      Cruise Operation Status Shift lever position signal / ON or OFF

      ON: Shift lever in D

      OFF: Shift lever not in D

      -
      Cruise Control Cruise control / ON or OFF

      ON: Cruise control set

      OFF: Cruise control not set

      -
      CCS Indicator M-CPU CRUISE main indicator (Main CPU) / ON or OFF

      ON: CRUISE main indicator light on

      OFF: CRUISE main indicator light off

      -
      CCS Ready M-CPU Cruise control system standby condition (Main CPU) / ON or OFF

      ON: Cruise control switch on

      OFF: Cruise control switch off

      -
      Main SW M-CPU Cruise control switch (Main CPU) / ON or OFF

      ON: Cruise control switch on

      OFF: Cruise control switch off

      -
      Cancel Switch CANCEL switch signal / ON or OFF

      ON: CANCEL switch on

      OFF: CANCEL switch off

      -
      SET/COAST Switch -SET switch signal / ON or OFF

      ON: -SET switch on

      OFF: -SET switch off

      -
      RES/ACC Switch +RES switch signal / ON or OFF

      ON: +RES switch on

      OFF: +RES switch off

      -
      Stp Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      -
      Cruise Request Driving Force* Cruise control driving force request signal / Min.: -51.2 kN, Max.: 51.2 kN Requested driving force displayed -

      *: for CVT

  2. ACTIVE TEST

    Tip:

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Combination Meter / Active Test.

    5. According to the display on the intelligent tester, perform the Active Test.

      Table 2. Combination Meter
      Tester Display Test Part Control Range Diagnostic Note
      Indicat. Lamp Cruise CRUISE main indicator light ON/OFF -