FUEL PUMP INSTALLATION


  1. INSPECT FITTING OF FUEL PUMP GAUGE RETAINER


    1. Inspect the fuel pump gauge retainer.


      1. Install the fuel pump gauge retainer to the fuel tank by hand with the fuel suction with pump disconnected.


        • If the fuel pump gauge retainer can be turned 180° or more by hand, reuse the retainer.

        • If the fuel pump gauge retainer cannot be turned 180° or more by hand, replace it with a new one.

        Tech Tips

        Check that there is no damage, dents, foreign matter, or other defects on the threads of the fuel tank.

  2. INSTALL FUEL SUCTION WITH PUMP ASSEMBLY


    1. A01ITPCE01
      Text in Illustration
      *1 New Gasket

      Install a new gasket onto the fuel tank.

    2. A01IN8RE01
      Text in Illustration
      *1 Notch
      *2 Protrusion

      Set the fuel suction with pump to the fuel tank.

      Note

      Make sure that the fuel sender gauge arm does not bend.

    3. Align the protrusion of the fuel suction with pump with the notch of the fuel tank.

    4. A01IPGSE02
      Text in Illustration
      *1

      Start Mark

      (Fuel Tank Side)
      *2

      Start Mark

      (Fuel Pump Gauge Retainer Side)
      A01ISM9 Front Side of Vehicle

      While holding the fuel suction with pump and gauge tube by hand to prevent it from tilting, align the start marks on a new fuel pump gauge retainer and fuel tank and tighten the fuel pump gauge retainer 180° by hand.

      Tech Tips

      Check that there is no damage, dents, foreign matter, or other defects on the threads of the fuel tank.

    5. A01INQ1E01
      Text in Illustration
      *1 SST (Plate)
      *2 SST (Claw)

      Temporarily install SST (plate and 2 claws) to the fuel pump gauge retainer.

      SST
      09808-14030

      Tech Tips


      • Be sure to use 2 SST (claws) as shown in the illustration.

      • Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.

    6. While securely pressing SST (claws) against the fuel pump gauge retainer ribs, install the 2 bolts.

      Tech Tips

      Install SST while pressing SST (claws) against the fuel pump gauge retainer (towards the center of SST).

    7. Install SST (handle).

    8. A01ITNVE02
      Text in Illustration
      *1

      Start Mark

      (Fuel Pump Gauge Retainer Side)
      A01ISM9 Turn
      A01ISER Front Side of Vehicle

      Tighten the fuel pump gauge retainer approximately 270° so that the start mark on the fuel pump gauge retainer is in the position shown in the illustration.

      SST
      09808-14030

      Note


      • Do not use any tools other than those specified in this operation. Damage to the fuel pump gauge retainer or fuel tank may result.

      • Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

      • Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.

      • Do not spin SST too fast or use an impact wrench as this may result in damage to components.

      • If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.

      Tech Tips


      • Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to tighten the fuel pump gauge retainer.

      • The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.

  3. CONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE


    1. A01ITD1E01

      Connect the No. 1 charcoal canister outlet hose to the fuel suction with pump.

  4. CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A01IS9AE01

      Connect the No. 1 fuel evaporation tube to the fuel suction with pump with the clip.

  5. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A01IPSPE01
      Text in Illustration
      *1 Fuel Tube Joint
      *2 Tube Joint Clip
      *3 O-Ring

      Push the fuel tube joint into the plug of the fuel suction with pump, and then install the tube joint clip.

      Note


      • Check that there are no scratches or foreign objects around the connected part of the fuel tube joint and plug before performing this work.

      • Check that the fuel tube joint is securely and fully inserted.

      • Check that the tube joint clip is on the collar of the fuel tube joint.

      • After installing the tube joint clip, check that the fuel tank main tube cannot be pulled out.

    2. A01ISOD

      Connect the fuel pump connector.

  6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. INSPECT FOR FUEL LEAK


    1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch to ON, and push the intelligent tester main switch on.

        Note

        Do not start the engine.

      3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

      4. Check that there are no leaks from the fuel system.

      5. Turn the ignition switch off.

      6. Disconnect the intelligent tester from the DLC3.

  8. INSTALL REAR FLOOR SERVICE HOLE COVER


    1. A01IP8E

      Install the rear floor service hole cover with new butyl tape.

  9. INSTALL REAR CENTER SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. Install the rear center seat Click here.

  10. INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. Install the rear No. 1 seat Click here.