Click here

FUEL INJECTOR REMOVAL

Click here
Click here Click here
  1. Click here

    DISCHARGE FUEL SYSTEM PRESSURE


    1. Discharge fuel system pressure (Click here).

  2. Click here

    REMOVE RADIATOR SUPPORT OPENING COVER


    1. A01IQMS

      Remove the 3 clips.

    2. Detach the 4 hooks and remove the radiator support opening cover.

  3. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  4. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  5. Click here

    REMOVE NO. 2 CYLINDER HEAD COVER


    1. A01IRS7

      Hold the rear of the cover and raise it to detach the 2 clips on the rear of the cover. Continue to raise the cover to detach the 2 clips on the front of the cover and remove the cover.

      Note:

      Attempting to detach both front and rear clips at the same time may cause the cover to break.

  6. Click here

    REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A01ISEG

      Disconnect the mass air flow meter connector.

    2. Detach the 2 clamps and disconnect the wire harness.

    3. A01IP4V

      Disconnect the 2 clamps.

    4. A01IPUC

      Disconnect the PCV hose.

    5. Loosen the band and remove the air cleaner cap.

  7. Click here

    REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. A01IQF0

      Detach the wire harness clamp from the air cleaner case.

    2. Remove the 3 bolts and air cleaner case.

  8. Click here

    REMOVE BATTERY CLAMP SUB-ASSEMBLY


    1. A01IQN6E01

      Disconnect the cable from the positive (+) battery terminal.

    2. Remove the bolt and loosen the nut.

    3. Remove the battery clamp.

  9. Click here

    REMOVE BATTERY

  10. Click here

    REMOVE BATTERY TRAY

  11. Click here

    DISCONNECT ENGINE WIRE


    1. Detach the 10 clamps, and then disconnect the connectors.

    2. A01INYW

      Remove the 3 bolts and 2 nuts, and then disconnect the engine wire.

  12. Click here

    REMOVE AIR TUBE


    1. A01IONW

      Disconnect the fuel vapor feed hose from the purge VSV.

    2. A01IN4RE01

      Disconnect the union to connector tube hose and vacuum hose.

      Table 1. Text in Illustration
      *1 Union To Connector Tube Hose
      *2 Vacuum Hose
      *3 No. 2 Air Hose
      *4 No. 1 Fuel Vapor Feed Hose

    3. Disconnect the No. 2 air hose and No. 1 fuel vapor feed hose.

    4. Remove the 2 bolts and air tube.

  13. Click here

    REMOVE WIRE HARNESS CLAMP BRACKET


    1. A01IU5T

      Remove the 2 nuts and wire harness clamp bracket.

  14. Click here

    DISCONNECT FUEL TUBE SUB-ASSEMBLY


    1. A01IURWE01

      Remove the No. 2 fuel pipe clamp.

      Table 2. Text in Illustration
      *1 Claw
    2. A01IUE6E01

      Wipe off any dirt on the fuel tube connector.

    3. Hold the fuel tube connector and install SST.

      09268-21010

    4. Turn SST to align the retainer inside the fuel tube connector with the chamfered part of SST.

    5. Insert SST into the fuel tube and hold it. Then push the fuel tube connector toward SST.

    6. Mount the retainer of the fuel tube connector onto the chamfered part of SST.

    7. A01IN53E17

      Slide SST and the fuel tube connector together towards the fuel tube until they make a "click" sound, and then disconnect the fuel tube.

      Table 3. Text in Illustration
      *1 O-Ring
      *2 Retainer
      *3 Pipe
      *4 Nylon Tube
      *5 Fuel Tube Connector

    8. Drain the fuel remaining inside the fuel tube.

    9. Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected parts.

  15. Click here

    REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    1. A01ISYL

      Remove the bolt and wire harness bracket.

    2. A01IUIW

      Remove the 2 bolts.

    3. A01IPXR

      Remove the bolt and the fuel delivery pipe.

    4. A01IP4K

      Remove the 2 No. 1 delivery pipe spacers.

  16. Click here

    REMOVE FUEL INJECTOR ASSEMBLY


    1. A01ISFF

      Pull the 4 fuel injector assemblies out of the fuel delivery pipe.

    2. A01IPID

      For reinstallation, attach a tag or label to the injector shaft.

      Note:

      Prevent entry of foreign objects by covering the fuel injector with plastic bags.

    3. A01ISRJ

      Remove the 4 injector vibration insulators.