FRONT CRANKSHAFT OIL SEAL INSTALLATION

INSTALL TIMING CHAIN COVER OIL SEAL
1. Apply MP grease to the lip of a new oil seal.
  Note
  
  Do not allow foreign matter to contact the lip of the oil seal.
  
  Do not allow MP grease to contact the dust seal.
2. Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.
  
  SST
  
  09223-22010
  Note
  - Wipe off any extra grease from the crankshaft.
  - Do not tap in the oil seal at an angle.
INSTALL CRANKSHAFT PULLEY
1. Text in Illustration
  
  *1 Hold
  
  *2 Turn
  
  Align the key groove of the pulley with the pulley set key.
2. Temporarily install the pulley with the pulley bolt.
3. Using SST, hold the pulley in place and tighten the bolt.
  
  for 86 mm (3.39 in.) Bolt Pitch Type:
  
  SST
  
  09213-58014 ( 91551-80840 )
  
  09330-00021
  
  for 64 mm (2.52 in.) Bolt Pitch Type:
  
  SST
  
  09213-54015
  
  09330-00021
  
  Torque:
  
  190 N*m { 1940 kgf*cm, 140 ft.*lbf }
  
  Tech Tips
  
  For the 64 mm (2.52 in.) bolt pitch type, the part number of the installation bolt for SST (crankshaft pulley holding tool) is 91551-00850 (quantity: 2).
INSTALL V-RIBBED BELT
1. Set the V-ribbed belt onto every pulley.
2. Attach a wrench to the hexagonal portion (A) or (B) of the V-ribbed belt tensioner assembly as shown in the illustration, and while rotating the V-ribbed belt tensioner assembly clockwise, remove the 5 mm hexagon wrench.
  
  Note
  
  Check that the V-ribbed belt is properly set to each pulley.
INSPECT V-RIBBED BELT
1. Check the V-ribbed belt for wear, cracks or other signs of damage.
  
  If any of the following defects is found, replace the V-ribbed belt.
  - The V-ribbed belt is cracked.
  - The V-ribbed belt is worn out to the extent that the cords are exposed.
  - The V-ribbed belt has chunks missing from the ribs.
2. Text in Illustration
  
  *a CORRECT
  
  *b INCORRECT
  
  Check that the V-ribbed belt fits properly in the ribbed grooves.
  
  Tech Tips
  
  Check with your hand to confirm that the belt has not slipped out of the grooves on the bottom to the pulley. If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt correctly.
INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
1. Install the reinforcement with the 4 bolts.
  
  Torque:
  
  99 N*m { 1010 kgf*cm, 73 ft.*lbf }
  
  Note
  
  Tighten the bolts in the order of C, B, D and A.

Text in Illustration
*1	Hold
*2	Turn

Text in Illustration
*a	CORRECT
*b	INCORRECT

ADD ENGINE OIL

Clean and install the oil pan drain plug together with a new gasket.

Torque:

37 N*m { 377 kgf*cm, 27 ft.*lbf }

Add new engine oil.

Standard Oil Grade

Oil Grade	Oil Viscosity (SAE)
API grade SL, SM or SN multigrade engine oil	20W-50 15W-40
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil	0W-20 5W-20 5W-30 10W-30

Standard Capacity

Item	Specified Condition
Drain and refill without oil filter change	3.9 liters (4.1 US qts, 3.4 Imp. qts)
Drain and refill with oil filter change	4.2 liters (4.4 US qts, 3.7 Imp. qts)
Dry fill	4.7 liters (5.0 US qts, 4.1 Imp. qts)

Install the oil filler cap.

INSPECT FOR ENGINE OIL LEAK
1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
INSTALL REAR ENGINE UNDER COVER RH
1. Install the under cover RH with the 5 clips.
INSTALL NO. 1 ENGINE UNDER COVER
1. Install the under cover with the 11 clips and 6 bolts.
INSTALL RADIATOR SUPPORT OPENING COVER
1. Attach the 4 hooks to install the radiator support opening cover.
2. Install the 3 clips.
INSTALL NO. 2 CYLINDER HEAD COVER
1. Attach the 4 clips to install the cover.
  Note
  
  Be sure to attach the clips securely.
  
  Do not apply excessive force or hit the cover to attach the clips. This may cause the cover to break.