ECD SYSTEM (for Swirl Control Valve), Diagnostic DTC:P052F

DTC Code DTC Name
P052F Glow Plug Control Module 1 System Voltage

DESCRIPTION

The glow plug controller assembly has a built-in voltage output stage during glow plug activation. The ECM activates the glow plugs by sending a signal indicating the required temperature to the glow plug controller assembly.

Also, the ECM sends control signals to the glow plug controller assembly via the LIN bus based on the values from various sensors.

When the glow plug control controller assembly detects a problem in the pre-heat system, it sends a report to the ECM via the LIN bus. The malfunction report is then stored inside the ECM.

DTC No. DTC Detection Condition Trouble Area
P052F

When glow plug controller assembly power supply voltage is low for 1.2 seconds or more.

(3 trip detection logic)

  • Glow plug controller assembly

  • Open or short in glow plug controller assembly circuit

  • ECM

WIRING DIAGRAM

A01IO2UE01

INSPECTION PROCEDURE

Note


  • When replacing the ECM, the ECM needs Registration and Initialization Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT GLOW PLUG RELAY ASSEMBLY


    1. Inspect the glow plug relay assembly Click here.


    NG

    REPLACE GLOW PLUG RELAY ASSEMBLY Click here

    OK

  2. CHECK GLOW PLUG CONTROLLER ASSEMBLY (BATT)


    1. A01IRZZE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to glow plug controller assembly)

      Disconnect the glow plug controller assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      X1-7 (BATT) - Body ground Always 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - RELAY - BATTERY) Click here

    OK

  3. CHECK GLOW PLUG CONTROLLER ASSEMBLY (POWER SOURCE CIRCUIT)


    1. A01INJHE05
      Text in Illustration
      *a

      Front view of wire harness connector

      (to glow plug controller assembly)

      Disconnect the glow plug controller assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C96-1 (+B) - Body ground Ignition switch ON 11 to 14 V
      C96-1 (+B) - Body ground Ignition switch ON Below 0.5 V

    NG

    CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - EFI MAIN RELAY) Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - ECM)


    1. Disconnect the glow plug controller assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C96-2 (GND) - C112-96 (EGCU) Always Below 1 Ω
      C96-2 (GND) or C112-96 (EGCU) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  5. REPLACE GLOW PLUG CONTROLLER ASSEMBLY


    1. Replace the glow plug controller assembly Click here


    NEXT

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NG

    REPLACE ECM Click here

    OK

    END

  7. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - RELAY - BATTERY)


    1. Disconnect the glow plug controller assembly connector.

    2. Remove the glow plug relay assembly.

    3. Remove the EFI MAIN relay from the engine room No. 1 relay block.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      X1-7 (BATT) - 3 (glow plug relay holder) Always Below 1 Ω
      4 (glow plug relay holder) - positive (+) battery terminal Always Below 1 Ω
      2 (glow plug relay holder) - 3 (EFI MAIN relay holder) Always Below 1 Ω
      1 (glow plug relay holder) - Body ground Always Below 1 Ω
      X1-7 (BATT) or 3 (glow plug relay holder) - Body ground Always 10 kΩ or higher
      4 (glow plug relay holder) or positive (+) battery terminal - Body ground Always 10 kΩ or higher
      2 (glow plug relay holder) or 3 (EFI MAIN relay holder) - Body ground Always 10 kΩ or higher

    OK

    CHECK ECM POWER SOURCE CIRCUIT Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

  8. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - EFI MAIN RELAY)


    1. Disconnect the glow plug controller assembly connector.

    2. Remove the EFI MAIN relay from the engine room No. 1 relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C96-1 (+B) - 3 (EFI MAIN relay holder) Always Below 1 Ω
      C96-1 (+B) or 3 (EFI MAIN relay holder) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  9. CHECK ECM POWER SOURCE CIRCUIT


    1. Check the ECM power source circuit Click here.

      Tech Tips

      If there are no malfunctions in the ECM power source circuit, recharge or replace the battery.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  10. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  11. REPLACE GLOW PLUG RELAY ASSEMBLY


    1. Replace the glow plug relay assembly.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  12. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END