ECD SYSTEM, Diagnostic DTC:P263E

DTC Code DTC Name
P263E Error High Temperature

DESCRIPTION

Refer to P052F Click here.

DTC No. DTC Detection Condition Trouble Area
P263E

Glow plug controller assembly determined to be overheating for 1.2 seconds or more

(3 trip detection logic)

  • Glow plug controller assembly

  • Open or short in glow plug controller assembly circuit

  • Glow plug

  • ECM

WIRING DIAGRAM

A01IOVHE01

INSPECTION PROCEDURE

Note

When replacing the ECM, the ECM needs Registration and Initialization Click here.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - ECM)


    1. Disconnect connectors of the glow plug controller assembly.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C96-2 (GND) - C84-96 (EGCU) Always Below 1 Ω
      C96-2 (GND) or C84-96 (EGCU) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - GLOW PLUG)


    1. Disconnect connectors of the glow plug controller assembly.

    2. Remove the glow plug connector from the glow plug.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      X1-4 (GL1) - X3-1 Always Below 1 Ω
      X1-1 (GL2) - X4-1 Always Below 1 Ω
      X1-6 (GL3) - X5-1 Always Below 1 Ω
      X1-5 (GL4) - X6-1 Always Below 1 Ω
      X1-4 (GL1) or X3-1 - Body ground Always 10 kΩ or higher
      X1-1 (GL2) or X4-1 - Body ground Always 10 kΩ or higher
      X1-6 (GL3) or X5-1 - Body ground Always 10 kΩ or higher
      X1-5 (GL4) or X6-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  3. INSPECT GLOW PLUG


    1. Inspect the glow plug Click here.


    NG

    REPLACE GLOW PLUG Click here

    OK

  4. REPLACE GLOW PLUG CONTROLLER ASSEMBLY


    1. Replace the glow plug controller assembly Click here.


    NEXT

  5. CHECK WHETHER DTC OUTPUT RECURS (DTC P263E)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Turn the ignition switch to ON and wait for 15 seconds or more [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Read the DTCs.

      Result
      Result Proceed to
      No DTC output A
      DTC P263E B

    B

    REPLACE ECM Click here

    A

    END

  6. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  7. REPLACE GLOW PLUG


    1. Replace the glow plug Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  8. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Turn the ignition switch to ON and wait for 15 seconds or more [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END