ECD SYSTEM (for Swirl Control Valve), Diagnostic DTC:P0237, P0238

DTC Code DTC Name
P0237 Turbocharger / Supercharger Boost Sensor "A" Circuit Low
P0238 Turbocharger / Supercharger Boost Sensor "A" Circuit High

DESCRIPTION

Refer to DTC P0236 Click here.

DTC No. DTC Detection Condition Trouble Area
P0237

Turbo pressure sensor assembly output voltage is 0.152 V or less for 0.1 seconds.

(3 trip detection logic)

  • Open or short in turbo pressure sensor assembly circuit

  • Turbo pressure sensor assembly

  • ECM
DTC No. DTC Detection Condition Trouble Area
P0238

Turbo pressure sensor assembly output voltage is 4.75 V or higher for 0.1 seconds.

(3 trip detection logic)

  • Open or short in turbo pressure sensor assembly circuit

  • Turbo pressure sensor assembly

  • ECM
Related Data List
DTC No. Data List

P0237

P0238

  • MAP

  • Atmosphere Pressure

WIRING DIAGRAM

Refer to DTC P0236 Click here.

INSPECTION PROCEDURE

Note


  • When replacing the ECM, the ECM needs Registration and Initialization Click here.

  • After replacing the turbo pressure sensor assembly, the ECM needs initialization Click here.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

    4. Compare the values when the ignition switch is ON.

      Standard
      Difference between the MAP and the Atmosphere Pressure is less than 7 kPa.

      Tech Tips

      Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.


    OK

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

    NG

    CHECK HARNESS AND CONNECTOR (TURBO PRESSURE SENSOR ASSEMBLY - ECM) Click here

  2. CHECK HARNESS AND CONNECTOR (TURBO PRESSURE SENSOR ASSEMBLY - ECM)


    1. Disconnect the turbo pressure sensor assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C97-3 (PIM) - C112-111 (PIM) Always Below 1 Ω
      C97-1 (VC) - C112-61 (VPIM) Always Below 1 Ω
      C97-2 (E) - C112-76 (EPIM) Always Below 1 Ω
      C97-3 (PIM) or C112-111 (PIM) - Body ground Always 10 kΩ or higher
      C97-1 (VC) or C112-61 (VPIM) - Body ground Always 10 kΩ or higher
      C97-2 (E) or C112-76 (EPIM) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (VC VOLTAGE)


    1. A01INJHE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to turbo pressure sensor assembly)

      Disconnect the turbo pressure sensor assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C97-1 (VC) - C97-2 (E) Ignition switch ON 4.5 to 5.5 V

    NG

    REPLACE ECM Click here

    OK

  4. REPLACE TURBO PRESSURE SENSOR ASSEMBLY


    1. Replace the turbo pressure sensor assembly Click here.

    2. Perform the upstream turbine pressure learning value reset Click here.


    NEXT

  5. CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Read the DTCs.

      Result
      Result Proceed to
      DTC P0237 or P0238 A
      No DTC output B

    B

    END

    A

  6. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  7. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.


    NEXT

    END