AUDIO AND VISUAL SYSTEM (for Radio and Display Type) HOW TO PROCEED WITH TROUBLESHOOTING

Tech Tips


  • Use the following procedure to troubleshoot the audio and visual system.

  • *: Use the intelligent tester.


  1. VEHICLE BROUGHT TO WORKSHOP


    NEXT

  2. CUSTOMER PROBLEM ANALYSIS


    • When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

    • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

    • The following 5 items are important points in problem analysis:

      What Vehicle model, system name
      When Date, time, occurrence frequency
      Where Road conditions
      Under what conditions? Driving conditions, weather conditions
      How did it happen? Problem symptoms

    NEXT

  3. INSPECT BATTERY VOLTAGE


    1. Measure the battery voltage.

      Standard voltage
      11 to 14 V

      • If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


      NEXT

  4. CHECK CABIN


    1. Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

      OK
      Condensation is not likely being produced and the temperature is not high or extremely low.

      Tech Tips


      • A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

      • The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.


      NG

      SET CABIN TO APPROPRIATE TEMPERATURE
      OK

  5. CHECK CAN COMMUNICATION SYSTEM*


    1. Check for DTC output Click here

      Result
      Result Proceed to
      DTCs are output A
      DTCs are not output B

      B

      GO TO CAN COMMUNICATION SYSTEM Click here

      A

  6. CHECK FOR DTC*


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      DTCs are output A
      DTCs are not output B

      B

      Go to step 10
      A

  7. CLEAR DTC*


    1. Clear the DTC Click here.

      Tech Tips

      The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.


      NEXT

  8. CHECK FOR DTC*


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      DTCs are output A
      DTCs are not output B

      Tech Tips


      • Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

      • If more information is needed, perform a recheck using the "System Check Mode" screen after rechecking for DTCs using the intelligent tester.

      • Check the DTCs and inspect the area that the code indicates.


      B

      Go to step 10
      A

  9. DIAGNOSTIC TROUBLE CODE CHART


    1. Find the output code in Diagnostic Trouble Code Chart Click here.


      NEXT

      Go to step 12

  10. PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table Click here.

      Result
      Result Proceed to
      Fault is not listed in Problem Symptoms Table A
      Fault is listed in Problem Symptoms Table B

      Tech Tips

      If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms Click here.


      B

      ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE
      A

  11. PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM


    1. Refer to Terminals of ECU Click here.


      NEXT

  12. CHECK CIRCUIT


    1. Adjust, repair or replace as necessary.


      NEXT

  13. RECHECK FOR DTC*


    1. After clearing DTCs, recheck for DTCs.


      NEXT

  14. PERFORM CONFIRMATION TEST


    NEXT
    END