Click here

VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1231/31

Click here
Click here Click here
DTC Code DTC Name
C1231/31 Steering Angle Sensor Circuit Malfunction
Click here

DESCRIPTION

The steering angle sensor signal is sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering angle sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1231/31 When the skid control ECU IG1 terminal voltage is 9.5 V or higher, the steering angle sensor malfunction signal is received.

  • Steering angle sensor (Spiral with sensor cable sub-assembly)

  • Steering angle sensor circuit

  • Steering angle sensor power supply
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Tip:

  • When DTC U0073/94, U0123/62 and/or U0126/63 is output together with DTC C1231/31, inspect and repair the trouble areas indicated by DTC U0073/94, U0123/62 and/or U0126/63 first (Click here).

  • When the speed sensor or the yaw rate sensor has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor assembly are output together with this steering angle sensor DTC, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering angle sensor.

Click here

PROCEDURE


  1. Click here

    CHECK DTC


    1. Clear the DTCs (Click here).

    2. Turn the ignition switch off.

    3. Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

    4. Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left, and check that no speed sensor and yaw rate sensor DTCs are output (Click here).

      Table 1. Result
      Result Proceed to
      No CAN communication system, speed sensor or yaw rate sensor DTC is output. A
      CAN communication system DTC is output. B
      Speed sensor or yaw rate sensor DTC is output. C
      Tip:

      • If there is a malfunction in the speed sensor or yaw rate sensor, an abnormal value may be output although the steering angle sensor is normal.

      • If speed sensor and yaw rate sensor assembly DTCs are output together with this steering angle sensor DTC, inspect and repair the speed and yaw rate sensors first, and then inspect and repair the steering angle sensor.


  2. Click here

    CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR POWER SOURCE TERMINAL)


    1. Turn the ignition switch off.

    2. Disconnect the steering angle sensor connector.

    3. A01ISJXE04

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H69-5 (IG) - Body ground Ignition switch ON 11 to 14 V
      H69-6 (BAT) - Body ground Always 11 to 14 V
      Table 2. Text in Illustration
      *1

      Front view of wire harness connector

      (to Steering Angle Sensor)

  3. Click here

    CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR GROUND TERMINAL)


    1. Turn the ignition switch off.

    2. Disconnect the steering angle sensor connector.

    3. A01ISJXE05

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H69-2 (ESS) - Body ground Always Below 1 Ω
      Table 3. Text in Illustration
      *1

      Front view of wire harness connector

      (to Steering Angle Sensor)

  4. Click here

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLYClick here

  5. Click here

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)Click here

  6. Click here

    REPAIR CIRCUIT INDICATED BY OUTPUT DTCClick here

  7. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR