Click here

VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1249

Click here
Click here Click here
DTC Code DTC Name
C1249 Open in Stop Light Switch Circuit
Click here

DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied. DTCs may be stored if either of the following occurs:


Tip:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.

DTC No. DTC Detection Condition Trouble Area
C1249

The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch assembly is on for 60 seconds or more.

  • Wire harness or connector

  • Stop light switch assembly

  • Skid control ECU (brake actuator assembly)
Click here

WIRING DIAGRAM

Refer to DTC C1380 (Click here).

Click here

INSPECTION PROCEDURE

Note:

  • When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (Click here).

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Click here

PROCEDURE


  1. Click here

    CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION


    1. Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

      OK
      The pedals were not depressed simultaneously.
      Tip:

      The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.

      If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.


  2. Click here

    CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

      OK
      Condition Illumination Condition
      Brake pedal depressed On
      Brake pedal released Off

  3. Click here

    READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Select the Data List on the GTS (Click here).

      Table 1. ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch assembly/ ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

    4. Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.

  4. Click here

    RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs (Click here).

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

    6. Check if the same DTC is output (Click here).

      Result
      Result Proceed to
      DTC C1249 is not output. A
      DTC C1249 is output. B
      Tip:

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).


  5. Click here

    CHECK TERMINAL VOLTAGE (STP TERMINAL)


    1. A01IQ6IE03

      Turn the ignition switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the A78 (for CVT) or A79 (except CVT) skid control ECU (brake actuator assembly) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage (for CVT)
      Tester Connection Condition Specified Condition
      A78-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
      A78-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Standard Voltage (except CVT)
      Tester Connection Condition Specified Condition
      A79-6 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
      A79-6 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Table 2. Text in Illustration
      *A for CVT
      *B except CVT
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))
      Tip:

      *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


  6. Click here

    INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Check the stop light switch assembly (Click here).

      OK
      The stop light switch assembly is normal.

  7. Click here

    CHECK TERMINAL VOLTAGE (STP AND STP2 TERMINAL)


    1. A01IQ6IE09

      Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A78 (for CVT) or A79 (except CVT) skid control ECU (brake actuator assembly) connector.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage (for CVT)
      Tester Connection Condition Specified Condition
      A78-30 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
      A78-30 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      A78-22 (STP2) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
      A78-22 (STP2) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Standard Voltage (except CVT)
      Tester Connection Condition Specified Condition
      A79-6 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
      A79-6 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      A79-24 (STP2) - Body ground Stop light switch assembly ON (Brake pedal depressed) 11 to 14 V*
      A79-24 (STP2) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V
      Table 3. Text in Illustration
      *A for CVT
      *B except CVT
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))
      Tip:

      *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


  8. Click here

    RECONFIRM DTC


    1. Reconnect the A78 (for CVT) or A79 (except CVT) skid control ECU (brake actuator assembly) connector.

    2. Clear the DTCs (Click here).

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

    6. Check if the same DTC is output (Click here).

      Result
      Result Proceed to
      DTC C1249 is not output. A
      DTC C1249 is output. B
      Tip:

      If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (Click here).


  9. Click here

    CLEAR DTC

  10. Click here

    USE SIMULATION METHOD TO CHECKClick here

  11. Click here

    REPLACE BRAKE ACTUATOR ASSEMBLYClick here

  12. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

  13. Click here

    REPLACE STOP LIGHT SWITCH ASSEMBLYClick here

  14. Click here

    INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)Click here

  15. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP OR STP2 CIRCUIT)