Click here

ECM INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL ECM


    1. A01IS74

      Install the No. 2 ECM bracket to the ECM with the 2 screws.

      3.0 N*m 31 kgf*cm 27 in.*lbf
    2. A01ISQ3

      Install the No. 1 ECM bracket to the ECM with the 2 screws.

      3.0 N*m 31 kgf*cm 27 in.*lbf

    3. Install the ECM with the 2 bolts.

      8.0 N*m 82 kgf*cm 71 in.*lbf

    4. Connect the 2 ECM connectors and lower the 2 levers.

      Note:

      • When connecting the connectors, make sure that dirt, water or other foreign matter does not get caught between the connectors and other parts.

      • Make sure that the 2 levers are securely lowered.

    5. Attach the wire harness clamp.

  2. Click here

    CONNECT NO. 2 AIR CLEANER INLET


    1. Connect the No. 2 air cleaner inlet to the vehicle body with the bolt.

      7.0 N*m 71 kgf*cm 62 in.*lbf
  3. Click here

    INSTALL NO. 1 AIR CLEANER INLET


    1. Attach the 2 claws to install the No. 1 air cleaner inlet.

    2. Install the clip.

  4. Click here

    INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. Install the air cleaner case with the 3 bolts.

      7.0 N*m 71 kgf*cm 62 in.*lbf

    2. Attach the wire harness clamp to the air cleaner case.

  5. Click here

    INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  6. Click here

    INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A01IPUC

      Connect the air cleaner cap with the band.

    2. Connect the PCV hose.

    3. A01IP4V

      Connect the 2 clamps.

    4. A01ISEG

      Attach the 2 clamps and connect the wire harness.

    5. Connect the mass air flow meter connector.

  7. Click here

    INSTALL NO. 2 CYLINDER HEAD COVER


    1. A01IRS7

      Attach the 4 clips to install the cover.

      Note:

      • Be sure to attach the clips securely.

      • Do not apply excessive force or hit the cover to attach the clips. This may cause the cover to break.

  8. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  9. Click here

    INSTALL RADIATOR SUPPORT OPENING COVER


    1. A01IQMS

      Attach the 4 hooks to install the radiator support opening cover.

    2. Install the 3 clips.

  10. Click here

    PERFORM INITIALIZATION

    Note:

    Perform the following procedure after replacing the throttle body assembly or any throttle body assembly components. The following procedure should also be performed if the throttle body assembly is cleaned.


    1. Turn the ignition switch to ON without operating the accelerator pedal.

      Note:

      If the accelerator pedal is operated, perform the above steps again.

    2. Connect the intelligent tester to the DLC3 and clear the DTCs (Click here).

    3. Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

      Standard idle speed
      580 to 680 rpm
      Note:

      • Be sure to perform this step with all accessories off.

      • Make sure that the shift lever is in neutral.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.

    5. Perform a road test and confirm that there are no abnormalities.